- 您现在的位置：买卖IC网 > PDF目录11354 > PIC24HJ128GP306A-E/MR (Microchip Technology)IC PIC MCU FLASH 128KB 64-QFN PDF资料下载
参数资料
| 型号： | PIC24HJ128GP306A-E/MR |
| 厂商： | Microchip Technology |
| 文件页数： | 4/20页 |
| 文件大小： | 0K |
| 描述： | IC PIC MCU FLASH 128KB 64-QFN |
| 标准包装： | 40 |
| 系列： | PIC® 24H |
| 核心处理器： | PIC |
| 芯体尺寸： | 16-位 |
| 速度： | 40 MIP |
| 连通性： | I²C，IrDA，LIN，SPI，UART/USART |
| 外围设备： | 欠压检测/复位，DMA，POR，PWM，WDT |
| 输入/输出数： | 53 |
| 程序存储器容量： | 128KB（43K x 24） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 16K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 3 V ~ 3.6 V |
| 数据转换器： | A/D 18x10b/12b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 64-VFQFN 裸露焊盘 |
| 包装： | 管件 |
PIC24HJXXXGPX06/X08/X10
DS80280G-page 12
2008 Microchip Technology Inc.
30. Module: SPI
SPI1 functionality for pin 34 (U1RX/SDI1/RF2) is
enabled by the SPI2 module. As a result, two side
effects occur:
1. RF2 functionality is disabled if the SPI2 module
is enabled.
2. This pin will not function as SDI1 if the SPI1
module is enabled.
This issue affects 64-pin devices only:
PIC24HJ64GP206
PIC24HJ128GP206
PIC24HJ256GP206
PIC24HJ128GP306
PIC24HJ64GP506
PIC24HJ128GP506
Work around
Two conditions apply:
1. If the SPI2 module is used, pin 34 cannot be
used as an I/O (RF2). It is recommended to
use another I/O pin.
2. If the SPI1 module is used, the SPI2 module
must also be enabled to gain SDI1 functionality
on pin 34. As an alternative, I/O (RF2) can be
configured as an input, which will allow pin 34
to function as SDI1.
31. Module: UART
The auto-baud feature may miscalculate for
certain baud rate and clock speed combinations,
resulting in a BRG value that is greater than or less
than the expected value by 1. This may result in
reception or transmission failures.
Work around
Test the auto-baud rate at various clock speed and
baud rate combinations that would be used in an
application. If an inaccurate BRG value is
generated, manually correct the baud rate in user
software.
32. Module: Device ID Register
On a few devices, the content of the Device ID
register can change from the factory programmed
default value immediately after RTSP or ICSP
Flash programming.
As a result, development tools will not recognize
these devices and will generate an error message
indicating that the device ID and the device part
number
do
not
match.
Additionally,
some
peripherals will be reconfigured and will not
function as described in the device data sheet.
Refer to Section 5. “Flash Programming”
(DS70191), of the “dsPIC33F Family Reference
Manual” for an explanation of RTSP and ICSP
Flash programming.
Work around
All RTSP and ICSP Flash programming routines
must be modified as follows:
1. No word programming is allowed. Any word
programming must be replaced with row
programming.
2. During row programming, load write latches as
described in 5.4.2.3 “Loading Write Latches”
of
Section
5.
“Flash
Programming”
(DS70191).
3. After latches are loaded, reload any latch
location (in a given row) that has 5 LSB set to
0x18, with the original data. For example,
reload one of the following latch locations with
the desired data:
0xXXXX18, 0xXXXX38, 0xXXXX58,
0xXXXX78, 0xXXXX98, 0xXXXXB8,
0xXXXXD8, 0xXXXXF8
4. Start
row
programming
by
setting
NVMOP<3:0> = ‘0001’ (memory row program
operation) in the NVMCON register.
5. After row programming is complete, verify the
contents of Flash memory.
6. If Flash verification errors are found, repeat
steps 2 through 5. If Flash verification errors
are found after a second iteration, report this
problem to Microchip.
Steps 1 through 5 in the work around are
implemented in MPLAB IDE version 8.00 or higher
for the MPLAB ICD 2, MPLAB REAL ICE
in-circuit emulator and PM3 tools.
相关PDF资料 |
PDF描述 |
|---|---|
| DEHR32E222KN2A | CAP CER 2200PF 250V 10% RADIAL |
| DEA1X3F820JN3A | CAP CER 82PF 3.15KV 5% RADIAL |
| PIC24FJ256GB106T-I/PT | IC PIC MCU FLASH 256K 64-TQFP |
| PIC18LF4610-I/PT | IC MCU FLASH 32KX16 44TQFP |
| GRM31CR71E335KA88L | CAP CER 3.3UF 25V 10% X7R 1206 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PIC24HJ128GP306A-I/MR | 功能描述:16位微控制器 - MCU 16 Bit MCU 40MIPS 128KB FLASH RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT |
| PIC24HJ128GP306A-I/PT | 功能描述:16位微控制器 - MCU 16 Bit MCU 40MIPS 128KB FLASH RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT |
| PIC24HJ128GP306AT-I/MR | 功能描述:16位微控制器 - MCU 16 Bit MCU 64LD 40MIPS 128KB FLASH RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT |
| PIC24HJ128GP306AT-I/PT | 功能描述:16位微控制器 - MCU 16 Bit MCU 40MIPS 128KB FLASH RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT |
| PIC24HJ128GP306-E/PT | 功能描述:16位微控制器 - MCU 16B MCU 64LD 40MIPS 128KB FLASH RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。