- 您现在的位置：买卖IC网 > PDF目录69305 > R5F21272SNFP 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP32 PDF资料下载
参数资料
| 型号： | R5F21272SNFP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP32 |
| 封装： | 7 X 7 MM, 0.80 MM PITCH, PLASTIC, LQFP-32 |
| 文件页数： | 14/52页 |
| 文件大小： | 620K |
| 代理商： | R5F21272SNFP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
39
ATmega165A/PA/325A/PA/3250A/PA/645A/P/6450A/P [DATASHEET]
8285E–AVR–02/2013
If Timer/Counter2 is not enabled, Power-down mode is recommended instead of Power-save mode.
The Timer/Counter2 can be clocked both synchronously and asynchronously in Power-save mode. The clock
source for the two modules can be selected independent of each other. If the Timer/Counter2 is not using the asyn-
chronous clock, the Timer/Counter Oscillator is stopped during sleep. If the Timer/Counter2 is not using the
synchronous clock, the clock source is stopped during sleep. Note that even if the synchronous clock is running in
Power-save, this clock is only available for Timer/Counter2.
10.8
Standby mode
When the SM2:0 bits are 110 and an external XTAL/resonator clock option is selected, the SLEEP instruction
makes the MCU enter Standby mode. This mode is identical to Power-down with the exception that the Oscillator is
kept running. From Standby mode, the device wakes up in six clock cycles.
10.9
Power Reduction Register
The Power Reduction Register (PRR), see ”PRR – Power Reduction Register” on page 42, provides a method to
stop the clock to individual peripherals to reduce power consumption. The current state of the peripheral is frozen
and the I/O registers can not be read or written. Resources used by the peripheral when stopping the clock will
remain occupied, hence the peripheral should in most cases be disabled before stopping the clock. Waking up a
module, which is done by clearing the bit in PRR, puts the module in the same state as before shutdown.
Module shutdown can be used in Idle mode and Active mode to significantly reduce the overall power consump-
tion. See ”ATmega165A: Supply current of I/O modules” on page 312 for examples. In all other sleep modes, the
clock is already stopped.
10.10 Minimizing power consumption
There are several issues to consider when trying to minimize the power consumption in an AVR controlled system.
In general, sleep modes should be used as much as possible, and the sleep mode should be selected so that as
few as possible of the device’s functions are operating. All functions not needed should be disabled. In particular,
the following modules may need special consideration when trying to achieve the lowest possible power
consumption.
10.10.1
Analog to Digital Converter
If enabled, the ADC will be enabled in all sleep modes. To save power, the ADC should be disabled before entering
any sleep mode. When the ADC is turned off and on again, the next conversion will be an extended conversion.
Refer to ”ADC - Analog to Digital Converter” on page 192 for details on ADC operation.
10.10.2
Analog Comparator
When entering Idle mode, the Analog Comparator should be disabled if not used. When entering ADC Noise
Reduction mode, the Analog Comparator should be disabled. In other sleep modes, the Analog Comparator is
automatically disabled. However, if the Analog Comparator is set up to use the Internal Voltage Reference as
input, the Analog Comparator should be disabled in all sleep modes. Otherwise, the Internal Voltage Reference will
be enabled, independent of sleep mode. Refer to ”AC - Analog Comparator” on page 188 for details on how to con-
figure the Analog Comparator.
10.10.3
Brown-out Detector
If the Brown-out Detector is not needed by the application, this module should be turned off. If the Brown-out
Detector is enabled by the BODLEVEL Fuses, it will be enabled in all sleep modes, and hence, always consume
power. In the deeper sleep modes, this will contribute significantly to the total current consumption. Refer to
”Brown-out detection” on page 45 for details on how to configure the Brown-out Detector.
10.10.4
Internal Voltage Reference
The Internal Voltage Reference will be enabled when needed by the Brown-out Detection, the Analog Comparator
or the ADC. If these modules are disabled as described in the sections above, the internal voltage reference will be
相关PDF资料 |
PDF描述 |
|---|---|
| R5F21264KXXXFP | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP32 |
| R5F21264JFP | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP32 |
| R5F21276SDXXXFP | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP32 |
| R5F21276KFP | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP32 |
| R5F21274SDFP | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP32 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| R5F21272SNFP#U0 | 制造商:Renesas Electronics Corporation 功能描述:MCU 16-Bit R8C CISC 8KB Flash 3.3V/5V 32-Pin LQFP Tray 制造商:Renesas Electronics Corporation 功能描述:MCU 16BIT R8C CISC 8KB FLASH 3.3V/5V 32LQFP - Trays 制造商:Renesas Electronics Corporation 功能描述:IC R8C/27 MCU FLASH 32LQFP |
| R5F21272SNFP#V0 | 功能描述:IC R8C/27 MCU FLASH 32LQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:R8C/2x/27 标准包装:250 系列:80C 核心处理器:8051 芯体尺寸:8-位 速度:16MHz 连通性:EBI/EMI，I²C，UART/USART 外围设备:POR，PWM，WDT 输入/输出数:40 程序存储器容量:- 程序存储器类型:ROMless EEPROM 大小:- RAM 容量:256 x 8 电压 - 电源 (Vcc/Vdd):4.5 V ~ 5.5 V 数据转换器:A/D 8x10b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:68-LCC（J 形引线） 包装:带卷 (TR) |
| R5F21272SNFP#V2 | 功能描述:MCU 8KB ROM 512B RAM 32-LQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:R8C/2x/27 标准包装:250 系列:80C 核心处理器:8051 芯体尺寸:8-位 速度:16MHz 连通性:EBI/EMI，I²C，UART/USART 外围设备:POR，PWM，WDT 输入/输出数:40 程序存储器容量:- 程序存储器类型:ROMless EEPROM 大小:- RAM 容量:256 x 8 电压 - 电源 (Vcc/Vdd):4.5 V ~ 5.5 V 数据转换器:A/D 8x10b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:68-LCC（J 形引线） 包装:带卷 (TR) |
| R5F21272SNFP#W4 | 制造商:Renesas Electronics Corporation 功能描述:MCU 3/5V 8+2K PB-FREE 32-LQFP T&R - Tape and Reel |
| R5F21272SNFP#X6 | 功能描述:MCU 8KB ROM 512B RAM 32-LQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:R8C/2x/27 标准包装:300 系列:78K0R/Ix3 核心处理器:78K/0R 芯体尺寸:16-位 速度:40MHz 连通性:3 线 SIO，I²C，LIN，UART/USART 外围设备:DMA，LVD，POR，PWM，WDT 输入/输出数:27 程序存储器容量:16KB（16K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:1K x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 5.5 V 数据转换器:A/D 8x10b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:38-SSOP 包装:托盘 |
发布紧急采购，3分钟左右您将得到回复。