- 您现在的位置：买卖IC网 > PDF目录69305 > R5F21272SNFP 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP32 PDF资料下载
参数资料
| 型号： | R5F21272SNFP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP32 |
| 封装： | 7 X 7 MM, 0.80 MM PITCH, PLASTIC, LQFP-32 |
| 文件页数： | 16/52页 |
| 文件大小： | 620K |
| 代理商： | R5F21272SNFP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
40
ATmega165A/PA/325A/PA/3250A/PA/645A/P/6450A/P [DATASHEET]
8285E–AVR–02/2013
disabled and it will not be consuming power. When turned on again, the user must allow the reference to start up
before the output is used. If the reference is kept on in sleep mode, the output can be used immediately. Refer to
”Internal voltage reference” on page 46 for details on the start-up time.
10.10.5
Watchdog Timer
If the Watchdog Timer is not needed in the application, the module should be turned off. If the Watchdog Timer is
enabled, it will be enabled in all sleep modes, and hence, always consume power. In the deeper sleep modes, this
will contribute significantly to the total current consumption. Refer to ”Watchdog Timer” on page 47 for details on
how to configure the Watchdog Timer.
10.10.6
Port pins
When entering a sleep mode, all port pins should be configured to use minimum power. The most important is then
to ensure that no pins drive resistive loads. In sleep modes where both the I/O clock (clk
I/O) and the ADC clock
(clk
ADC) are stopped, the input buffers of the device will be disabled. This ensures that no power is consumed by
the input logic when not needed. In some cases, the input logic is needed for detecting wake-up conditions, and it
will then be enabled. Refer to the section ”Digital Input Enable and Sleep modes” on page 65 for details on which
pins are enabled. If the input buffer is enabled and the input signal is left floating or have an analog signal level
close to V
CC/2, the input buffer will use excessive power.
For analog input pins, the digital input buffer should be disabled at all times. An analog signal level close to V
CC/2
on an input pin can cause significant current even in active mode. Digital input buffers can be disabled by writing to
the Digital Input Disable Registers (DIDR1 and DIDR0). Refer to ”DIDR1 – Digital Input Disable Register 1” on
page 191 and ”DIDR0 – Digital Input Disable Register 0” on page 208 for details.
10.10.7
JTAG Interface and On-chip Debug System
If the On-chip debug system is enabled by the OCDEN Fuse and the chip enter Power down or Power save sleep
mode, the main clock source remains enabled. In these sleep modes, this will contribute significantly to the total
current consumption. There are three alternative ways to avoid this:
Disable OCDEN Fuse
Disable JTAGEN Fuse
Write one to the JTD bit in MCUCR
The TDO pin is left floating when the JTAG interface is enabled while the JTAG TAP controller is not shifting data.
If the hardware connected to the TDO pin does not pull up the logic level, power consumption will increase. Note
that the TDI pin for the next device in the scan chain contains a pull-up that avoids this problem. Writing the JTD bit
in the MCUCR register to one or leaving the JTAG fuse unprogrammed disables the JTAG interface.
相关PDF资料 |
PDF描述 |
|---|---|
| R5F21264KXXXFP | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP32 |
| R5F21264JFP | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP32 |
| R5F21276SDXXXFP | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP32 |
| R5F21276KFP | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP32 |
| R5F21274SDFP | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP32 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| R5F21272SNFP#U0 | 制造商:Renesas Electronics Corporation 功能描述:MCU 16-Bit R8C CISC 8KB Flash 3.3V/5V 32-Pin LQFP Tray 制造商:Renesas Electronics Corporation 功能描述:MCU 16BIT R8C CISC 8KB FLASH 3.3V/5V 32LQFP - Trays 制造商:Renesas Electronics Corporation 功能描述:IC R8C/27 MCU FLASH 32LQFP |
| R5F21272SNFP#V0 | 功能描述:IC R8C/27 MCU FLASH 32LQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:R8C/2x/27 标准包装:250 系列:80C 核心处理器:8051 芯体尺寸:8-位 速度:16MHz 连通性:EBI/EMI，I²C，UART/USART 外围设备:POR，PWM，WDT 输入/输出数:40 程序存储器容量:- 程序存储器类型:ROMless EEPROM 大小:- RAM 容量:256 x 8 电压 - 电源 (Vcc/Vdd):4.5 V ~ 5.5 V 数据转换器:A/D 8x10b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:68-LCC（J 形引线） 包装:带卷 (TR) |
| R5F21272SNFP#V2 | 功能描述:MCU 8KB ROM 512B RAM 32-LQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:R8C/2x/27 标准包装:250 系列:80C 核心处理器:8051 芯体尺寸:8-位 速度:16MHz 连通性:EBI/EMI，I²C，UART/USART 外围设备:POR，PWM，WDT 输入/输出数:40 程序存储器容量:- 程序存储器类型:ROMless EEPROM 大小:- RAM 容量:256 x 8 电压 - 电源 (Vcc/Vdd):4.5 V ~ 5.5 V 数据转换器:A/D 8x10b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:68-LCC（J 形引线） 包装:带卷 (TR) |
| R5F21272SNFP#W4 | 制造商:Renesas Electronics Corporation 功能描述:MCU 3/5V 8+2K PB-FREE 32-LQFP T&R - Tape and Reel |
| R5F21272SNFP#X6 | 功能描述:MCU 8KB ROM 512B RAM 32-LQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:R8C/2x/27 标准包装:300 系列:78K0R/Ix3 核心处理器:78K/0R 芯体尺寸:16-位 速度:40MHz 连通性:3 线 SIO，I²C，LIN，UART/USART 外围设备:DMA，LVD，POR，PWM，WDT 输入/输出数:27 程序存储器容量:16KB（16K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:1K x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 5.5 V 数据转换器:A/D 8x10b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:38-SSOP 包装:托盘 |
发布紧急采购，3分钟左右您将得到回复。