- 您现在的位置：买卖IC网 > PDF目录69312 > R5F2L3AACDFP 8-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP100 PDF资料下载
参数资料
| 型号： | R5F2L3AACDFP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP100 |
| 封装： | 14 X 14 MM, 0.50 MM PITCH, PLASTIC, LQFP-100 |
| 文件页数： | 18/74页 |
| 文件大小： | 959K |
| 代理商： | R5F2L3AACDFP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页
26
2588F–AVR–06/2013
ATtiny261/461/861
mencing normal operation. The watchdog oscillator is used for timing this real-time part of the
start-up time. The number of WD oscillator cycles used for each time-out is shown in Table 6-2.
6.2.1
External Clock
To drive the device from an external clock source, CLKI should be driven as shown in Figure 6-
2. To run the device on an external clock, the CKSEL Fuses must be programmed to “0000”.
Figure 6-2.
External Clock Drive Configuration
When this clock source is selected, start-up times are determined by the SUT Fuses as shown in
When applying an external clock, it is required to avoid sudden changes in the applied clock fre-
quency to ensure stable operation of the MCU. A variation in frequency of more than 2% from
one clock cycle to the next can lead to unpredictable behavior. It is required to ensure that the
MCU is kept in Reset during such changes in the clock frequency.
Note that the system clock prescaler can be used to implement run-time changes of the internal
clock frequency. See “System Clock Prescaler” on page 31 for details.
6.2.2
High-Frequency PLL Clock
The internal PLL generates a clock signal with a frequency eight times higher than the source
input. The PLL uses the output of the internal 8 MHz oscillator as source and the default setting
generates a fast peripheral clock signal of 64 MHz.
Table 6-2.
Number of Watchdog Oscillator Cycles
Typ Time-out
Number of Cycles
4 ms
512
64 ms
8K (8,192)
Table 6-3.
Start-up Times for the External Clock Selection
SUT1:0
Start-up Time from Power-
down and Power-save
Additional Delay from
Reset
Recommended Usage
00
6 CK
14CK
BOD enabled
01
6 CK
14CK + 4 ms
Fast rising power
10
6 CK
14CK + 64 ms
Slowly rising power
11
Reserved
EXTERNAL
CLOCK
SIGNAL
CLKI
GND
相关PDF资料 |
PDF描述 |
|---|---|
| R5F2L3ACCNFP | 8-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP100 |
| R5F2L38ACNFA | 8-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP80 |
| R5F2L38CCNFP | 8-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP80 |
| R5F2L387CDFP | 8-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP80 |
| R5F2L387CNFP | 8-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP80 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| R5F2L3AACDFP#U1 | 制造商:Renesas Electronics Corporation 功能描述: |
| R5F2L3AACDFP#V0 | 制造商:Renesas Electronics Corporation 功能描述:R8C/L3AC 96K+4K/10K 100LQFP14X14 -40-+85 - Trays |
| R5F2L3AACNFA#U0 | 制造商:Renesas Electronics Corporation 功能描述:R8CL3AC 96+4KB 1.8/5.5V -20 TO 85C 100QFP - Trays 制造商:Renesas Electronics Corporation 功能描述:IC MCU 16BIT 96KB FLASH 100LQFP |
| R5F2L3AACNFP#30 | 制造商:Renesas Electronics Corporation 功能描述:IC MCU 16BIT 96KB FLASH 100LQFP 制造商:Renesas Electronics Corporation 功能描述:R8C Series 16 bit 10 kB RAM 96 kB Flash Single Chip Microcontroller SMT-LQFP-100 |
| R5F2L3AACNFP#V0 | 功能描述:MCU 1KB FLASH 96K ROM 100-LQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:R8C/Lx/3AC 标准包装:250 系列:56F8xxx 核心处理器:56800E 芯体尺寸:16-位 速度:60MHz 连通性:CAN，SCI，SPI 外围设备:POR，PWM，温度传感器，WDT 输入/输出数:21 程序存储器容量:40KB（20K x 16） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:6K x 16 电压 - 电源 (Vcc/Vdd):2.25 V ~ 3.6 V 数据转换器:A/D 6x12b 振荡器型:内部 工作温度:-40°C ~ 125°C 封装/外壳:48-LQFP 包装:托盘 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323 |
发布紧急采购，3分钟左右您将得到回复。