参数资料
| 型号： | RDK-236 |
| 厂商： | Power Integrations |
| 文件页数： | 8/30页 |
| 文件大小： | 0K |
| 描述： | KIT REF DESIGN PFS714EG |
| 标准包装： | 1 |
| 系列： | HiperPFS™ |
| 主要目的： | 电源管理，功率因数校正 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | PFS714EG |
| 主要属性： | 347W，370 ~ 390V 输出，90 ~ 264VAC 输入 |
| 已供物品： | 板 |
| 其它名称： | 596-1418 |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
PFS704-729EG
to decay the power MOSFET on-time to zero. At peak power
(V E ~5 V) the shutdown time will be approximately 5 ms. The
internal error-voltage is held at 0 V for as long as the input peak
voltage is below the brown-in (I UV+ ) threshold. The internal
error-voltage controlled slew to 0 V gradually reduces the switch
on-time to zero to deplete energy stored in the boost choke as
well as input EMI filter for power-down. Once the error-voltage
I V < 48 μ A
I V > 59 μ A
PFS704-716
reaches zero volts the controller is effectively in an off-state
(gated by 5 ms timer) and will restart once all the conditions of
soft-start are satisfied.
V IN
The brown-out threshold is reduced to I UV-SS during start-up until
the FEEDBACK pin exceeds approximately 5.8 V. Temporarily
~140 VAC
~170 VAC
PI-5470-110810
reducing the brown-out threshold prevents false turn-off at high
power start-up when the voltage drop across the input bridge
rectifier and filter stage may cause the rectified input to sag
below the brown-out threshold.
Fast Output Voltage Overvoltage Protection (FB OV )
The FEEDBACK pin features a means to detect an output
overvoltage condition through the FEEDBACK pin and disables
the power MOSFET until the sensed output voltage falls below
the FB OV threshold. A deglitch filter (~2 m s) is used to prevent
the controller from falsely triggering this mode. An FB OV event in
excess of the 2 m s delay will terminate the switch cycle immediately.
This detection circuit also includes some hysteresis.
Output Voltage Undervoltage Protection (FB UV )
The FEEDBACK pin features an undervoltage detection to
detect an output overload or a broken feedback loop. If the IC
detects the falling edge on the FEEDBACK pin that has fallen
below FB UV threshold, it will turn-off the internal power MOSFET
and re-initiate the start-up sequence. Similar to the FB OV detection,
this mode has a deglitch filter of approximately 100 m s.
VCC Undervoltage Protection (UVLO)
The BIAS POWER (VCC) pin has an undervoltage lock-out
protection which inhibits the IC from starting unless the applied
V CC voltage is above the V CC+ threshold. The IC initiates a
soft-start once the VCC pin voltage exceeds the V CC+ threshold.
After start-up the IC will continue to operate until the VCC pin
voltage has fallen below V CC- level. The absolute maximum
voltage of the VCC pin is 15 V which must be externally limited
to prevent damage to the IC.
Over-Current Protection
The device includes a cycle-by-cycle over-current-protection
(OCP) mode which protects the device in the event of a
catastrophic fault. The OCP mode in the PFS704-716 is input
line dependent as shown in Figure 10. The intention of OCP in
this device is strictly protection of the internal power MOSFET
and is not intended to protect the converter from output
short-circuit or overload fault conditions.
The PFS704-716 controller latches the high line OCP for a 1/2
line cycle and updates the OCP status after the expiration of a
5 ms block-out timer. This feature has particular benefit for
hard-start after an AC line cycle drop where the peak detector
may falsely detect a low input line condition even though the
input is at high input line.
8
Rev. F 12/12
Figure 10. Line Dependant OCP.
The leading edge blanking circuit inhibits the current limit
comparator for a short time (t LEB ) after the power MOSFET is
turned on. This leading edge blanking time must be set so that
current spikes caused by capacitance and rectifier reverse
recovery time will not cause premature termination of the
MOSFET conduction.
Safe Operating Range (SOA) Mode
Since the cycle-by-cycle OCP mechanism described above
does not prevent the possibility of inductor current “stair-
casing”, an SOA mode is required. Rapid build up of the device
current can occur in event of inductor saturation or when the
input and output voltages are equal (non or very short inductor
reset time).
The SOA mode is triggered whenever the device reaches
current limit (I OCP ) and the on-time is less than t SOA .
The SOA mode forces an off-time equal to t OCP and pulls the
internal error-voltage (V E ) down to approximately 1/2 of its set
value.
Open FEEDBACK Pin Protection
The FEEDBACK pin also features a static current of I FB that is
continuously sourced out of the pin to protect against a fault
related to an open FEEDBACK pin. The internal current source
introduces a static offset to the output regulation which must be
accounted for in selecting the output feedback regulation
components.
Hysteretic Thermal Shutdown
The thermal shutdown circuitry senses the controller die
temperature. The threshold is set at 118 °C typical with a 50 °C
hysteresis. When the die temperature rises above this threshold
(118 °C +8/-7 °C), the power MOSFET switching is disabled and
remains disabled until the die temperature falls by ~50 °C, at
which point the device will re-initiate a soft-start and start-up
sequence.
www.powerint.com
相关PDF资料 |
PDF描述 |
|---|---|
| RECE-20279-001E-01 | RCPT IPEX MHF |
| RF2594-000 | BD540-30 |
| RF2873-000 | POLYSWITCH 1.25A RESET FUSE RAD |
| RGEF1000-1 | POLYSWITCH PTC RESET 10A HOLD |
| RGEF1000-2 | POLYSWITCH PTC RESET 10A HLD T/R |
相关代理商/技术参数 |
参数描述 |
|---|---|
| RDK-239 | 功能描述:LED 照明开发工具 HV 150W RESONANT CONVERTER KIT RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装: |
| RDK-242 | 功能描述:电源管理IC开发工具 TOPSwitch-JX REF. DESIGN KIT RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| RDK-248 | 功能描述:LED 照明开发工具 UNIVERSAL PFC 180W HiperPFS KIT RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装: |
| RDK-249 | 功能描述:线性和开关式电源 HiperTFS Ref Des Kit 14.W Stby, 300W PS RoHS:否 制造商:TDK-Lambda 产品:Switching Supplies 开放式框架/封闭式:Enclosed 输出功率额定值:800 W 输入电压:85 VAC to 265 VAC 输出端数量:1 输出电压（通道 1）:20 V 输出电流（通道 1）:40 A 商用/医用: 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:Rack 长度: 宽度: 高度: |
| RDK-251 | 功能描述:LED 照明开发工具 LinkSwitch-PL Ref Des Kit, 5W Dim RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装: |
发布紧急采购，3分钟左右您将得到回复。