- 您现在的位置：买卖IC网 > PDF目录69323 > RTC-7301SFB REAL TIME CLOCK, PDSO24 PDF资料下载
参数资料
| 型号： | RTC-7301SFB |
| 元件分类： | 时钟/数据恢复及定时提取 |
| 英文描述： | REAL TIME CLOCK, PDSO24 |
| 封装： | SSOP-24 |
| 文件页数： | 20/28页 |
| 文件大小： | 274K |
| 代理商： | RTC-7301SFB |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页
RTC - 7301 SF / DG
Page - 24
MQ332-05
13. Application notes
13-1. Notes on handling
This module uses a C-MOS IC to realize low power consumption.
Carefully note the following cautions when
handling.
(1) Static electricity
While this module has built-in circuitry designed to protect it against electrostatic discharge, the chip
could still be damaged by a large discharge of static electricity. Containers used for packing and
transport should be constructed of conductive materials. In addition, only soldering irons, measurement
circuits, and other such devices which do not leak high voltage should be used with this module, which
should also be grounded when such devices are being used.
(2) Noise
If a signal with excessive external noise is applied to the power supply or input pins, the device may
malfunction or "latch up." In order to ensure stable operation, connect a filter capacitor (preferably
ceramic) of greater that 0.1F as close as possible to the power supply pins (between VDD and GNDs).
Also, avoid placing any device that generates high level of electronic noise near this module.
* Do not connect signal lines to the shaded area in the figure shown in Fig. 1 and, if possible, embed
this area in a GND land.
(3) Voltage levels of input pins
When the input pins are at the mid-level, this will cause increased current consumption and a reduced
noise margin, and can impair the functioning of the device. Therefore, try as much as possible to apply
the voltage level close to VDD or GND.
(4) Handling of unused pins
Since the input impedance of the input pins is extremely high, operating the device with these pins in
the open circuit state can lead to unstable voltage level and malfunctions due to noise. Therefore, pull-
up or pull-down resistors should be provided for all unused input pins.
13-2. Notes on packaging
(1) Soldering temperature conditions
If the temperature within the package exceeds 260, the characteristics of the crystal oscillator will be
degraded and it may be damaged. Therefore, always check the mounting temperature before mounting
this device. Also, check again if the mounting conditions are later changed.
* See Fig. 2 for the soldering conditions of SMD products.
(2) Mounting equipment
While this module can be used with general-purpose mounting equipment, the internal crystal oscillator
may be damaged in some circumstances, depending on the equipment and conditions. Therefore, be
sure to check this. In addition, if the mounting conditions are later changed, the same check should be
performed again.
(3) Ultrasonic cleaning
Depending on the usage conditions, there is a possibility that the crystal oscillator will be damaged by
resonance during ultrasonic cleaning. Since the conditions under which ultrasonic cleaning is carried
out (the type of cleaner, power level, time, state of the inside of the cleaning vessel, etc.) vary widely,
this device is not warranted against damage during ultrasonic cleaning.
(4) Mounting orientation
This device can be damaged if it is mounted in the wrong orientation. Always confirm the orientation of
the device before mounting.
(5) Leakage between pins
Leakage between pins may occur if the power is turned on while the device has condensation or dirt on
it. Make sure the device is dry and clean before supplying power to it.
Fig. 1: Example GND Pattern
Fig. 2: Soldering Conditions of SMD Products
Air Reflow Profile
RTC - 7301 SF
( SSOP-24pin )
RTC - 7301 DG
( DIP-18pin )
30 s
± 10 s
90 s
± 30 s
+150
°C ± 10 °C
+200
°C
+235
°C ± 5 °C
+240
°C Max.
Time[ s ]
10 s
± 1 s
Temperature[
°C ]
相关PDF资料 |
PDF描述 |
|---|---|
| RTC6581 | REAL TIME CLOCK, PDIP24 |
| RTPXA270C0C312 | 312 MHz, RISC PROCESSOR, PBGA356 |
| RCPXA270C0C520 | 520 MHz, MICROPROCESSOR, PBGA356 |
| RV5C387A-F | 0 TIMER(S), REAL TIME CLOCK, PDSO10 |
| RX-4571LC | REAL TIME CLOCK, PDSO12 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| RTC-840 | 制造商:AAEON 制造商全称:AAEON 功能描述:Intel?? Corea?￠ Duo U2500 1.2 GHz Processor |
| RTC-8563JE | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Real-Time Clock |
| RTC-8563SA | 制造商:EPSONTOYOCOM 制造商全称:Epson ToYoCom 功能描述:RTC-8563SA |
| RTC-8563SJE | 制造商:EPSONTOYOCOM 制造商全称:Epson ToYoCom 功能描述:RTC-8563SA |
| RTC-8564JE | 制造商:Epson Toyocom Corporation 功能描述:32.768kHz 275nA@3ViTyp.j 3.0V (typ.) 7.0~5.4~1.5mm +85 -40 5}23ppm@+25/3.0V 7mm 5.4mm 1.5mm 制造商:Epson Toyocom Corporation 功能描述:RTC I2C BUS INTERFACE SMD VSOJ-20 制造商:Epson Toyocom Corporation 功能描述:RTC I2C BUS INTERFACE, SMD, VSOJ-20 制造商:Epson Toyocom Corporation 功能描述:IC, RTC, FULL CALENDAR, VSOJ-20; Clock Format:12Hr / 24Hr; Clock IC Type:RTC; Supply Voltage Min:1.8V; Supply Voltage Max:5.5V; Digital IC Case Style:VSOJ; No. of Pins:20; IC Interface Type:I2C; Operating Temperature Min:-40C ;RoHS Compliant: Yes 制造商:Epson Toyocom 功能描述:RTC module,I2C Bus,Alarm,timer func |
发布紧急采购，3分钟左右您将得到回复。