- 您现在的位置：买卖IC网 > PDF目录192296 > S29GL032A11BFIR43 (SPANSION LLC) 64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY PDF资料下载
参数资料
| 型号： | S29GL032A11BFIR43 |
| 厂商： | SPANSION LLC |
| 元件分类： | PROM |
| 英文描述： | 64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY |
| 中文描述： | 2M X 16 FLASH 3V PROM, 110 ns, PBGA48 |
| 封装： | 8.15 X 6.15 MM, LEAD FREE, FBGA-48 |
| 文件页数： | 54/95页 |
| 文件大小： | 3585K |
| 代理商： | S29GL032A11BFIR43 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页当前第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页
58
S29GL-A
S29GL-A_00_A12 May 21, 2008
Da ta
Sh e e t
Figure 9.3 Program Suspend/Program Resume
9.6
Chip Erase Command Sequence
Chip erase is a six bus cycle operation. The chip erase command sequence is initiated by writing two unlock
cycles, followed by a set-up command. Two additional unlock write cycles are then followed by the chip erase
command, which in turn invokes the Embedded Erase algorithm. The device does not require the system to
preprogram prior to erase. The Embedded Erase algorithm automatically preprograms and verifies the entire
memory for an all zero data pattern prior to electrical erase. The system is not required to provide any
controls or timings during these operations. Table 10.2 on page 61 and Table 10.1 on page 62 show the
address and data requirements for the chip erase command sequence.
When the Embedded Erase algorithm is complete, the device returns to the read mode and addresses are no
longer latched. The system can determine the status of the erase operation by using DQ7, DQ6, or DQ2.
Refer to Write Operation Status on page 63 for information on these status bits.
Any commands written during the chip erase operation are ignored. However, note that a hardware reset
immediately terminates the erase operation. If this occurs, the chip erase command sequence should be
reinitiated once the device returns to reading array data, to ensure data integrity.
Figure 10.1 on page 59 illustrates the algorithm for the erase operation. Refer to Table 16.5 on page 76 for
parameters, and Figure 16.7 on page 80 for timing diagrams.
Program Operation
or Write-to-Buffer
Sequence in Progress
Write Program Suspend
Command Sequence
Command is also valid for
Erase-suspended-program
operations
Autoselect and SecSi Sector
read operations are also allowed
Data cannot be read from erase- or
program-suspended sectors
Write Program Resume
Command Sequence
Read data as
required
Done
reading?
No
Yes
Write address/data
XXXh/30h
Device reverts to
operation prior to
Program Suspend
Write address/data
XXXh/B0h
Wait 15
μs
相关PDF资料 |
PDF描述 |
|---|---|
| S29GL032A90TAIR20 | 64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY |
| S29GL032A90TAIR22 | 64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY |
| S29GL032A90TAIR23 | 64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY |
| S29GL032A90TAIR30 | 64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY |
| S29GL032A90TAIR32 | 64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY |
相关代理商/技术参数 |
参数描述 |
|---|---|
| S29GL032A11FAIR10 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY |
| S29GL032A11FAIR11 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY |
| S29GL032A11FAIR12 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY |
| S29GL032A11FAIR13 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY |
| S29GL032A11FAIR20 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:64 MEGABIT 32MEGABIT 3.0 BOLT ONLY PAGE MODE FLASH MEMORY |
发布紧急采购，3分钟左右您将得到回复。