- 您现在的位置：买卖IC网 > PDF目录69327 > S80C188EB-13 (INTEL CORP) 16-BIT, 13 MHz, MICROPROCESSOR, PQFP80 PDF资料下载
参数资料
| 型号： | S80C188EB-13 |
| 厂商： | INTEL CORP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 16-BIT, 13 MHz, MICROPROCESSOR, PQFP80 |
| 封装： | EIAJ, QFP-80 |
| 文件页数： | 55/59页 |
| 文件大小： | 1928K |
| 代理商： | S80C188EB-13 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页当前第55页第56页第57页第58页第59页
80C186EB80C188EB 80L186EB80L188EB
ERRATA
An 80C186EB80L186EB with a STEPID value of
0001H has the following known errata A device with
a STEPID of 0001H can be visually identified by the
presence
of an ‘‘A’’ alpha character next to the
FPO number The FPO number location is shown in
Figures 4 5 and 6
1 A19ONCE is not latched by the rising edge of
RESIN A19ONCE must remain active (LOW) at
all times to remain in the ONCE Mode Removing
A19ONCE after RESIN is high will return all out-
put pins to a driving state
however
the
80C186EB will remain in a reset state
2 During interrupt acknowledge (INTA) bus cycles
the bus controller will ignore the state of the
READY pin if the previous bus cycle ignored the
state of the READY pin This errata can only oc-
cur if the Chip-Select Unit is being used All active
chip-selects must be programmed to use READY
(RDY bit must be programmed to a 1) if wait-
states are required for INTA bus cycles
3 CLKOUT will transition off the rising edge of
CLKIN rather than the falling edge of CLKIN This
does not affect any bus timings other than TCD
4 RESIN has a hysterisis of only 130 mV It is rec-
ommended that RESIN be driven by a Schmitt
triggered device to avoid processor lockup during
reset using an RC circuit
5 SINT1 will only go active for one clock period
when a receive or transmit interrupt is pending
(ie
it does not remain active until the S1STS
register is read) If SINT1 is to be connected to
any of the processor interrupt lines (INT0 – INT4)
then it must be latched by user logic
An 80C186EB80L186EB with a STEPID value of
0001H or 0002H has the following known errata A
device with a STEPID of 0002H can be visually iden-
tified by noting the presence of a ‘‘B’’ ‘‘C’’ ‘‘D’’ or
‘‘E’’ alpha character next to the FPO number The
FPO number location is shown in Figures 4 5 and 6
1 An internal condition with the interrupt controller
can cause no acknowledge cycle on the INTA1
line in response to INT1 This errata only occurs
when Interrupt 1 is configured in cascade mode
and a higher priority interrupt exists This errata
will not occur consistantly it is dependent on in-
terrupt timing
REVISION HISTORY
This data sheet replaces the following data sheets
270803-004 80C186EB
270885-003 80C188EB
270921-003 80L186EB
270920-003 80L188EB
272311-001 SB80C188EBSB80L188EB
272312-001 SB80C186EBSB80L186EB
59
相关PDF资料 |
PDF描述 |
|---|---|
| S80C188EB-20 | 16-BIT, 20 MHz, MICROPROCESSOR, PQFP80 |
| SB80C188EB-20 | 16-BIT, 20 MHz, MICROPROCESSOR, PQFP80 |
| SB80C188EB-25 | 16-BIT, 25 MHz, MICROPROCESSOR, PQFP80 |
| S80L186EB-13 | 16-BIT, 13 MHz, MICROPROCESSOR, PQFP80 |
| SB80L188EB-13 | 16-BIT, 13 MHz, MICROPROCESSOR, PQFP80 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| S80C188EB20 | 制造商:INTEL 制造商全称:Intel Corporation 功能描述:16-BIT HIGH-INTEGRATION EMBEDDED PROCESSORS |
| S80C188EB25 | 功能描述:IC MPU 16-BIT 5V 25MHZ 80-MQFP RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微处理器 系列:- 标准包装:2 系列:MPC8xx 处理器类型:32-位 MPC8xx PowerQUICC 特点:- 速度:133MHz 电压:3.3V 安装类型:表面贴装 封装/外壳:357-BBGA 供应商设备封装:357-PBGA（25x25） 包装:托盘 |
| S80C188EB-25 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:16-Bit Microprocessor |
| S80C188EC13 | 制造商:INTEL 制造商全称:Intel Corporation 功能描述:16-BIT HIGH-INTEGRATION EMBEDDED PROCESSORS |
| S80C188EC-13 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:16-Bit Microprocessor |
发布紧急采购，3分钟左右您将得到回复。