参数资料
型号: SAB-C161O-L16M
厂商: INFINEON TECHNOLOGIES AG
元件分类: 微控制器/微处理器
英文描述: 16-BIT, 16 MHz, MICROCONTROLLER, PQFP80
封装: 0.65 MM PITCH, PLASTIC, MQFP-80
文件页数: 6/43页
文件大小: 741K
代理商: SAB-C161O-L16M
1996 Intermediate Version
Semiconductor Group
13
C161
Interrupt System
With an interrupt response time within a range from just 315 ns to 750 ns (in case of internal
program execution), the C161 is capable of reacting very fast to the occurence of non-deterministic
events.
The architecture of the C161 supports several mechanisms for fast and flexible response to service
requests that can be generated from various sources internal or external to the microcontroller. Any
of these interrupt requests can be programmed to being serviced by the Interrupt Controller or by
the Peripheral Event Controller (PEC).
In contrast to a standard interrupt service where the current program execution is suspended and
a branch to the interrupt vector table is performed, just one cycle is ‘stolen’ from the current CPU
activity to perform a PEC service. A PEC service implies a single byte or word data transfer between
any two memory locations with an additional increment of either the PEC source or the destination
pointer. An individual PEC transfer counter is implicity decremented for each PEC service except
when performing in the continuous transfer mode. When this counter reaches zero, a standard
interrupt is performed to the corresponding source related vector location. PEC services are very
well suited, for example, for supporting the transmission or reception of blocks of data. The C161
has 8 PEC channels each of which offers such fast interrupt-driven data transfer capabilities.
A separate control register which contains an interrupt request flag, an interrupt enable flag and an
interrupt priority bitfield exists for each of the possible interrupt sources. Via its related register, each
source can be programmed to one of sixteen interrupt priority levels. Once having been accepted
by the CPU, an interrupt service can only be interrupted by a higher prioritized service request. For
the standard interrupt processing, each of the possible interrupt sources has a dedicated vector
location.
Fast external interrupt inputs are provided to service external interrupts with high precision
requirements. These fast interrupt inputs feature programmable edge detection (rising edge, falling
edge or both edges).
Software interrupts are supported by means of the ‘TRAP’ instruction in combination with an
individual trap (interrupt) number.
The following table shows all of the possible C161 interrupt sources and the corresponding
hardware-related interrupt flags, vectors, vector locations and trap (interrupt) numbers:
相关PDF资料
PDF描述
SED1540FOA 4 X 73 DOTS DOT MAT LCD DRVR AND DSPL CTLR, PQFP100
ST62T10CN3 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PDSO20
SED1222TXX 16 X 60 DOTS DOT MAT LCD DRVR AND DSPL CTLR, UUC
ST72651R6T1 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP64
SAB80C517-N-T40 8-BIT, MROM, 12 MHz, MICROCONTROLLER, PQCC84
相关代理商/技术参数
参数描述
SAB-C161O-L25M 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Infineon Technologies AG 功能描述:Micro,16-Bit,2KB RAM ,25Mhz
SAB-C161O-L25M HA 功能描述:16位微控制器 - MCU 16-Bit SNGL-Chip Microcontroller RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT
SABC161OL25MHA 功能描述:16位微控制器 - MCU RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT
SAB-C161O-L25M-HA 制造商:Rochester Electronics LLC 功能描述: 制造商:Infineon Technologies AG 功能描述:
SABC161OL25MHAXT 制造商:Infineon Technologies AG 功能描述:MCU 16-Bit C166 CISC/RISC ROMLess 5V 80-Pin MQFP