参数资料
型号: SC16IS850LIPW
厂商: NXP Semiconductors N.V.
元件分类: 连接器件
英文描述: Single UART with I2C-bus-SPI interface, 128 bytes of transmit and receive FIFOs, IrDA SIR built-in support
封装: SC16IS850LIBS<SOT616-3 (HVQFN24)|<<http://www.nxp.com/packages/SOT616-3.html<1<Always Pb-free,;SC16IS850LIBS<SOT616-3 (HVQFN24)|<<http://www.nxp.com/packages/SOT616-3.htm
文件页数: 17/60页
文件大小: 755K
代理商: SC16IS850LIPW
SC16IS850L
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 1 — 22 July 2011
17 of 60
NXP Semiconductors
SC16IS850L
Single UART with I
2
C-bus/SPI interface
7.11 RS-485 features
7.11.1
Auto RS-485 RTS control
Normally the RTS pin is controlled by MCR[1], or if hardware flow control is enabled, the
logic state of the RTS pin is controlled by the hardware flow control circuitry. AFCR2[4] will
take the precedence over the other two modes; once this bit is set, the transmitter will
control the state of the RTS pin. The transmitter automatically asserts the RTS pin
(logic 0) once the host writes data to the transmit FIFO, and de-asserts RTS pin (logic 1)
once the last bit of the data has been transmitted.
To use the auto RS-485 RTS mode the software would have to disable the hardware
flow control function.
7.11.2
RS-485 RTS inversion
AFCR2[5] reverses the polarity of the RTS pin if the UART is in auto RS-485 RTS mode.
When the transmitter has data to be sent it will de-asserts the RTS pin (logic 1), and when
the last bit of the data has been sent out the transmitter asserts the RTS pin (logic 0).
7.11.3
Auto 9-bit mode (RS-485)
AFCR2[0] is used to enable the 9-bit mode (Multi-drop or RS-485 mode). In this mode of
operation, a ‘master’ station transmits an address character followed by data characters
for the addressed ‘slave’ stations. The slave stations examine the received data and
interrupt the controller if the received character is an address character (parity bit = 1).
To use the automatic 9-bit mode, the software would have to disable the hardware and
software flow control functions.
7.11.3.1
Normal Multi-drop mode
The 9-bit Mode in AFCR2[0] is enabled, but not Special Character Detect (EFR[5]). The
receiver is set to Force Parity 0 (LCR[5:3] = 111) in order to detect address bytes.
With the receiver initially disabled, it ignores all the data bytes (parity bit = 0) until an
address byte is received (parity bit = 1). This address byte will cause the UART to set the
parity error. The UART will generate a line status interrupt (IER[2] must be set to ‘1’ at this
time), and at the same time puts this address byte in the RX FIFO. After the controller
examines the byte it must make a decision whether or not to enable the receiver; it should
enable the receiver if the address byte addresses its ID address, and must not enable the
receiver if the address byte does not address its ID address.
If the controller enables the receiver, the receiver will receive the subsequent data until
being disabled by the controller after the controller has received a complete message
from the ‘master’ station. If the controller does not disable the receiver after receiving a
message from the ‘master’ station, the receiver will generate a parity error upon receiving
another address byte. The controller then determines if the address byte addresses its ID
address, if it is not, the controller then can disable the receiver. If the address byte
addresses the ‘slave’ ID address, the controller takes no further action, and the receiver
will receive the subsequent data.
相关PDF资料
PDF描述
SC18IM700IPW Master I?C-bus controller with UART interface
SC2092 Pressure Transducer, Series 19 mm, Uncompensated, Pressure Range: 0 psi to 30 psi, Absolute, flush mount, 10 Vdc excitation
SC2092-400-15 Circular Connector; MIL SPEC:MIL-DTL-38999 Series III; Body Material:Metal; Series:TVS06; Number of Contacts:55; Connector Shell Size:23; Connecting Termination:Crimp; Circular Shell Style:Straight Plug; Body Style:Straight
SC2092-600-15 Circular Connector; No. of Contacts:55; Series:TVS06; Body Material:Metal; Connecting Termination:Crimp; Connector Shell Size:23; Circular Contact Gender:Socket; Circular Shell Style:Straight Plug; Insert Arrangement:23-55
SC6433 BWTV CAMERA SYNC PULSE GENERATOR
相关代理商/技术参数
参数描述
SC16IS850LIPW,118 制造商:NXP Semiconductors 功能描述:Single UART with I2C-bus/SPI interface 制造商:NXP Semiconductors 功能描述:SC16IS850LIPW/TSSOP24/REEL13// - Tape and Reel 制造商:NXP Semiconductors 功能描述:IC INTERFACE UART
SC16IS850LIPW,128 制造商:NXP Semiconductors 功能描述:SC16IS850LIPW/TSSOP24/RAIL13T// - Tape and Reel 制造商:NXP Semiconductors 功能描述:Slave I2C-bus/SPI Interface, 128 bytes
SC16lS741 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Smart, simple solutions for the 12 most common design concerns
SC16M11D70 功能描述:标准环形接头 Trim Trio Socket 16 AWG Contact Sz 16 RoHS:否 制造商:TE Connectivity / AMP 系列:Multimate III+ 触点尺寸: 触点类型:Pin (Male) 触点材料: 触点电镀:Tin over Nickel 触点类型2: 电流额定值:13 A 电压额定值:
SC16M11D70REV 功能描述:标准环形接头 Trim Trio Socket 16 AWG Contact Sz 16 RoHS:否 制造商:TE Connectivity / AMP 系列:Multimate III+ 触点尺寸: 触点类型:Pin (Male) 触点材料: 触点电镀:Tin over Nickel 触点类型2: 电流额定值:13 A 电压额定值: