参数资料
| 型号： | SC4525ASETRT |
| 厂商： | Semtech |
| 文件页数： | 9/19页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK 3A 8SOIC |
| 标准包装： | 1 |
| 类型： | 降压（降压） |
| 输出数： | 1 |
| 输入电压： | 8 V ~ 28 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 300kHz ~ 1.3MHz |
| 电流 - 输出： | 3A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm Width）裸露焊盘 |
| 包装： | 标准包装 |
| 供应商设备封装： | 8-SOIC-EP |
| 产品目录页面： | 1358 (CN2011-ZH PDF) |
| 其它名称： | SC4525ASEDKR |
SC4525A
Applications Information
Table 2: Fault conditions and protections
Condition
Fault
Protective Action frequency
IL>ILimit, IL>ILimit, V FB <0.8V Over current current
Cycle-by-cycle limit at limit with
VSS/EN Falling Persistent over Cycle-by-cycle Shutdown, then retry
SS/EN<1.9V
or short circuit
(Hiccup)
0.4V to 1.23V
Not switching & hiccup armed
2mA
Load dependent
Pulling the SS/EN pin below 0.2V shuts off the regulator
Operation
The SC4525A is a constant-frequency, peak current-
mode, step-down switching regulator with an integrated
28V, 3.6A power NPN transistor. Programmable switching
frequency makes the regulator design more flexible. With
the peak current-mode control, the double reactive poles
of the output LC filter are reduced to a single real pole by
the inner current loop. This simplifies loop compensation
and achieves fast transient response with a simple Type-2
compensation network.
As shown in Figure 2, the switch collector current is
sensed with an integrated 4. m W sense resistor. The
sensed current is summed with a slope-compensating
ramp before it is compared with the transconductance
error amplifier (EA) output. The PWM comparator trip
point determines the switch turn-on pulse width. The
current-limit comparator ILIM turns off the power switch
when the sensed signal exceeds the 20mV current-limit
threshold.
Driving the base of the power transistor above the
input power supply rail minimizes the power transistor
saturation voltage and maximizes efficiency. An external
bootstrap circuit (formed by the capacitor C and the
diode D in Figure ) generates such a voltage at the BST
pin for driving the power transistor.
Shutdown and Soft-Start
The SS/EN pin is a multiple-function pin. An external
capacitor (4.7nF to 22nF) connected from the SS pin to
ground sets the soft-start and overload shutoff times of
the regulator (Figure 3). The effect of V SS/EN on the SC4525A
is summarized in Table .
Table 1: SS/EN operation modes
SS/EN Mode Supply Current
<0.2V Shutdown 18uA @ 5Vin
Switching
SS/EN 0.4V to 1.23V Mode Not switching Supply Current 2mA
<0.2V 1.23V to 2.1V Shutdown & hiccup disabled 18uA @ 5Vin
Load dependent
>2.1V Switching
1.23V to 2.1V Switching & hiccup disabled
>2.1V Switching & hiccup armed
and reduces the input supply current to 8μA (V IN = 5V).
When the SS/EN pin is released, the soft-start capacitor
is charged with an internal .6μA current source (not
shown in Figure 3). As the SS/EN voltage exceeds 0.4V,
the internal bias circuit of the SC4525A turns on and the
SC4525A draws 2mA from V IN . The .6μA charging current
turns off and the 2μA current source I C in Figure 3 slowly
charges the soft-start capacitor.
The error amplifier EA in Figure 2 has two non-inverting
inputs. The non-inverting input with the lower voltage
predominates. One of the non-inverting inputs is biased
to a precision V reference and the other non-inverting
input is tied to the output of the amplifier A . Amplifier A
produces an output V = 2(V SS/EN - .23V). V is zero and COMP
is forced low when V SS/EN is below .23V. During start up,
the effective non-inverting input of EA stays at zero until
the soft-start capacitor is charged above .23V. Once V SS/EN
exceeds .23V, COMP is released. The regulator starts to
switch when V COMP rises above 0.4V. If the soft-start interval
is made sufficiently long, then the FB voltage (hence the
output voltage) will track V during start up. V SS/EN must be
at least .83V for the output to achieve regulation. Proper
soft-start prevents output overshoot. Current drawn from
the input supply is also well controlled.
Overload / Short-Circuit Protection
Table 2 lists various fault conditions and their
corresponding protection schemes in the SC4525A.
Condition Fault Protective Action
Cycle-by-cycle limit at
IL>ILimit, V FB >0.8V Over current
programmed
V FB >0.8V Over
programmed frequency foldback
IL>ILimit, V FB <0.8V Over current
(Hiccup)
SS/EN<1.9V or short circuit frequency foldback
VSS/EN Falling Persistent over current Shutdown, then retry
Tj>160C Over temperature Shutdown
Tj>160C Over temperature Shutdown
As summarized in Table , overload shutdown is disabled
during soft-start (V SS/EN <2. V). In Figure 3, the reset input of
the overload latch B 2 will remain high if the SS/EN voltage
is below 2. V. Once the soft-start capacitor is charged
above 2. V, the output of the Schmitt trigger B goes high,
the reset input of B 2 goes low and hiccup becomes armed.
9
相关PDF资料 |
PDF描述 |
|---|---|
| SC4525CSETRT | IC REG BUCK ADJ 3A 8SOIC |
| SC4525DSETRT | IC REG BUCK ADJ 3A 8SOIC |
| SC458IMLTRT | IC REG CTRLR PWM 44-MLP |
| SC4620MLTRT | IC REG BUCK ADJ 2.5A 20MLPQ |
| SC4624AMLTRT | IC REG BUCK ADJ 4A 20MLPQ |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SC4525C | 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:28V 3A Step-Down Switching Regulator Thermal Shutdown |
| SC4525CSETRT | 功能描述:IC REG BUCK ADJ 3A 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| SC4525D | 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:18V, 3A, 350kHz Step-Down Switching Regulator |
| SC4525DEVB | 制造商:SEMTECH 制造商全称:Semtech Corporation 功能描述:18V, 3A, 350kHz Step-Down Switching Regulator |
| SC4525DSETRT | 功能描述:IC REG BUCK ADJ 3A 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 类型:升压（升压） 输出类型:两者兼有 输出数:1 输出电压:5V，2 V ~ 16.5 V 输入电压:2 V ~ 16.5 V PWM 型:- 频率 - 开关:45kHz 电流 - 输出:50mA 同步整流器:无 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:8-DIP（0.300"，7.62mm） 包装:管件 供应商设备封装:8-PDIP |
发布紧急采购，3分钟左右您将得到回复。