- 您现在的位置：买卖IC网 > PDF目录22044 > SE98ATL,147 (NXP Semiconductors)IC TEMP SENSOR DDR 3.6V 8-HXSON PDF资料下载
参数资料
| 型号： | SE98ATL,147 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 9/43页 |
| 文件大小： | 849K |
| 描述： | IC TEMP SENSOR DDR 3.6V 8-HXSON |
| 标准包装： | 1 |
| 功能： | 温度监控系统（传感器） |
| 传感器类型： | 内部 |
| 感应温度： | -40°C ~ 125°C |
| 精确度： | ±4°C（最小值） |
| 拓扑： | ADC（三角积分型），寄存器库 |
| 输出类型： | I²C?/SMBus? |
| 输出警报： | 是 |
| 输出风扇： | 是 |
| 电源电压： | 1.7 V ~ 3.6 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-WFDFN 裸露焊盘 |
| 供应商设备封装： | 8-WSON |
| 包装： | 标准包装 |
| 其它名称： | 568-4780-6 |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页
SE98A_4
?NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 04 25 November 2009
9 of 43
NXP Semiconductors
SE98A
DDR memory module temp sensor, 1.7 V to 3.6 V
7.3.2.2 Critical trip
The T
th(crit)
temperature setting is programmed in the Critical Alarm Trip register (04h) as
modified by hysteresis as programmed in the Configuration register. When the
temperature reaches the critical temperature value in this register (and EVENT
is
enabled), the EVENT
output asserts and cannot be de-asserted until the temperature
drops below the critical temperature threshold. The EVENT
cannot be cleared through the
Clear EVENT
bit (CEVNT) or SMBus ALERT.
The Critical Alarm Trip should always be set above the Upper Boundary Alarm Trip.
" Advisory notification:
NXP device: Requires one conversion cycle (125 ms) after setting the Alarm
Window before comparing the alarm limit with temperature register to ensure that
there is correct data in the temperature register before comparing with the Alarm
Window and operating EVENT
output.
Competitor devices: Compares the Alarm Window with temperature register at any
time, so they get the EVENT
output immediately when new T
th(crit)
and
EVENT
output are set at the same time.
Work-around: Wait at least 125 ms before enabling EVENT
output (EOCTL = 1).
Intel will change Nehalem BIOS so that T
th(crit)
is set for more than 125 ms before
EVENT
output is enabled and Event value is checked.
1. Set T
th(crit)
.
2. Doing something else (make sure that exceeds 125 ms).
3. Enable the EVENT
output (EOCTL = 1).
4. Wait 20 約.
5. Read Event value.
SE98B will compare Alarm Window and temperature register immediately after
setting.
7.3.3 Event operation modes
7.3.3.1 Comparator mode
In comparator mode, the EVENT
output behaves like a window-comparator output that
asserts when the temperature is outside the window (e.g., above the value programmed in
the Upper Boundary Alarm Trip register or below the value programmed in the Lower
Boundary Alarm Trip register or above the Critical Alarm Trip resister if T
th(crit)
only is
selected). Reads/writes on the registers do not affect the EVENT
output in comparator
mode. The EVENT
signal remains asserted until the temperature goes inside the alarm
window or the window thresholds are reprogrammed so that the current temperature is
within the alarm window.
The comparator mode is useful for thermostat-type applications, such as turning on a
cooling fan or triggering a system shutdown when the temperature exceeds a safe
operating range.
7.3.3.2 Interrupt mode
In interrupt mode, EVENT
asserts whenever the temperature crosses an alarm window
threshold. After such an event occurs, writing a 1 to the Clear EVENT
bit in the
configuration register de-asserts the EVENT
output until the next trigger condition occurs.
相关PDF资料 |
PDF描述 |
|---|---|
| EEM08DRMD-S288 | CONN EDGECARD 16POS .156 EXTEND |
| AIML-0805-1R5K-T | INDUCTOR MULTILAYER 1.5UH 0805 |
| EB43-S1R504XS | CONN EDGEBOARD DUAL 100POS 3A |
| LFX200EB-04FN256I | IC FPGA 200K GATES 256-BGA |
| NCP500SN26T1 | IC REG LDO 2.6V .15A 5TSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SE98ATP | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:DDR memory module temp sensor, 1.7 V to 3.6 V |
| SE98ATP,147 | 功能描述:板上安装温度传感器 I2 CLOCAL +/-1OC 1.7-3.6V TSDIMM RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| SE98ATP,547 | 功能描述:板上安装温度传感器 PROG TWI DIG 3.6V RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| SE98PW | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:SO-DIMM SMBus/I2C-bus temperature sensor |
| SE98PW,118 | 功能描述:板上安装温度传感器 I2C LOCAL +/- 2OC RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
发布紧急采购，3分钟左右您将得到回复。