参数资料
型号: SI2457-D-GT
厂商: Silicon Laboratories Inc
文件页数: 17/60页
文件大小: 0K
描述: IC ISOMODEM GLOBAL DAA 24TSSOP
标准包装: 62
系列: *
Si2457/34/15/04
24
Rev. 1.3
Sn=x
Set S-register n to value x (where n and x are decimal values).
Vn
Result code type (see Table 12 on page 38).
V0
Numeric result codes.
V1
Verbal result codes
Xn
Call Progress Monitor (CPM)—This command controls which CPM signals are monitored
and reported to the host from the Si2457/34/15/04. (See Table 12 on page 38.)
X0
Basic results; disable CPM—Blind dial (does not wait for dial tone). CONNECT message
does not include speed.
X1
Extended results; disable CPM—Blind dial. CONNECT message includes speed.
X2
Extended results and detect dial tone only—Add dial tone detection to X1 mode. Does not
blind dial.
X3
Extended results and detect busy only—Add busy tone detection to X1 mode.
X4
Extended results, full CPM—Full CPM enabled, CONNECT message includes speed.
X5
Extended results—Full CPM enabled including ringback detection. Adds ringback detection
to X4 mode.
Yn
Long space disconnect—Modem hangs up after 1.5 seconds or more of continuous space
while on-line.
Y0
Disable.
Y1
Enable.
Z
Hard Reset—This command is functionally equivalent to pulsing the RESET pin low. (See
:E
Read from serial EEPROM.
:I
Interrupt Read—This command causes the ISOmodem to report the lower 8 bits of the
interrupt register I/O Control 0 (U70). The CID, OCD, PPD, and RI bits also are cleared, and
the INT pin (INT bit in parallel mode) is deactivated on this read.
:M
Write to serial EEPROM.
:P
Program RAM Write—This command is used to upload firmware supplied by Silicon Labs to
the Si2457/34/15/04. The format for this command is AT:Paaaa,xxxx,yyyy,.... where aaaa is
the first address in hexadecimal and xxxx,yyyy,.... is data in hexadecimal. Only one :P com-
mand is allowed per AT command line. No other commands can be concatenated in the :P
command line. This command is only for use with special files provided by Silicon Laborato-
ries. Do not attempt to use this command for any other purpose.
:R
User-Access Register Read—This command allows the user to read from the user-access
registers (see "6. User-Access Registers (U-Registers)" on page 44). The format is “AT:Raa”,
where:
aa = user-access address in hexadecimal.
The “AT:R” command causes all the U- registers to be displayed.
Table 8. Basic AT Command Set (Command Defaults in Bold) (Continued)
Command
Action
相关PDF资料
PDF描述
SI3016-BS IC LINE-SIDE DAA 16SOIC
SI3452D-B01-GM IC POE CONTROLLER MIDSPAN 40QFN
SI4126-F-BMR IC SYNTHESIZER RF2/IF 28MLP
SI5040-A-GM IC TXRX XFP 10GBPS 32LGA
SI5100-G-BC IC TXRX SERIAL/DESERIAL 195CBGA
相关代理商/技术参数
参数描述
SI2457-D-GTR 制造商:Silicon Laboratories Inc 功能描述:56 KBPS, V.90 ISOMODEM SYSTEM- 制造商:Silicon Laboratories Inc 功能描述:56 KBPS, V.90 ISOMODEM SYSTEM-SIDE - LEAD-FREE - Tape and Reel 制造商:Silicon Laboratories Inc 功能描述:IC ISOMODEM GLOBAL DAA 24TSSOP 制造商:Silicon Laboratories Inc 功能描述:56 kbps V90 ISOmodem System-Side PBF
Si2457FS08-EVB 功能描述:网络开发工具 16-pin Si2457+Si3008 ISOmodem Eval Board RoHS:否 制造商:Rabbit Semiconductor 产品:Development Kits 类型:Ethernet to Wi-Fi Bridges 工具用于评估:RCM6600W 数据速率:20 Mbps, 40 Mbps 接口类型:802.11 b/g, Ethernet 工作电源电压:3.3 V
Si2457FS18-EVB 功能描述:网络开发工具 16-pin Si2457+Si3018 ISOmodem Eval Board RoHS:否 制造商:Rabbit Semiconductor 产品:Development Kits 类型:Ethernet to Wi-Fi Bridges 工具用于评估:RCM6600W 数据速率:20 Mbps, 40 Mbps 接口类型:802.11 b/g, Ethernet 工作电源电压:3.3 V
SI2457-FT 功能描述:电信线路管理 IC CONTACT SILICON LABS FOR AVAILABILITY RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray
Si2457FT08-EVB 功能描述:网络开发工具 24-pin Si2457+Si3008 ISOmodem Eval Board RoHS:否 制造商:Rabbit Semiconductor 产品:Development Kits 类型:Ethernet to Wi-Fi Bridges 工具用于评估:RCM6600W 数据速率:20 Mbps, 40 Mbps 接口类型:802.11 b/g, Ethernet 工作电源电压:3.3 V