- 您现在的位置：买卖IC网 > PDF目录10997 > SI3210-FT (Silicon Laboratories Inc)IC SLIC/CODEC PROGRAMMBL 38TSSOP PDF资料下载
参数资料
| 型号： | SI3210-FT |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 81/148页 |
| 文件大小： | 0K |
| 描述： | IC SLIC/CODEC PROGRAMMBL 38TSSOP |
| 标准包装： | 50 |
| 系列： | ProSLIC® |
| 功能： | 用户线路接口概念（SLIC），CODEC |
| 接口： | PCM，SPI |
| 电路数： | 1 |
| 电源电压： | 3.3V，5V |
| 电流 - 电源： | 88mA |
| 功率（瓦特）： | 700mW |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 38-TFSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 38-TSSOP |
| 包装： | 管件 |
| 包括： | BORSCHT 功能，DTMF 生成和解码，FSK 生成，脉冲测量生成，语音回送测试模式 |
| 其它名称： | 336-1168 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页当前第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页
Si3210/Si3211
38
Rev. 1.61
Not
Recommended
fo
r N
ew
D
esi
gn
s
2.2.3. MOSFET/Transformer Circuit Option Using
the Si3210M
The MOSFET/transformer circuit option (shown in
Figure 11 on page 20) offers higher power efficiencies
across a larger input voltage range. Depending on the
transformer’s primary inductor value and the switching
frequency, the input voltage (VDC) can range from 3.3 V
to 35 V. Therefore, it is possible to power the entire
ProSLIC solution from a single 3.3 V or 5 V power
supply. By nature of a dc-dc converter’s operation, peak
and average input currents can become large with small
input voltages. Consider this when selecting the
appropriate input voltage and power rating for the VDC
power supply (number of REN supported).
For this solution, an N-channel power MOSFET (M1)
switches the current flow through a power transformer,
T1. T1 is specified in “AN45: Design Guide for the
Si3210 DC-DC Converter” and includes several taps on
the primary side to facilitate a wide range of input
voltages. The Si3210M version of the Si3210 must be
used for the application circuit depicted in Figure 11
because the DCFF pin is used to drive M1 directly and,
therefore, must be the same polarity as DCDRV.
DCDRV is not used in this circuit option; connecting
DCFF and DCDRV together is not recommended.
2.2.4. DC-DC Converter Architecture
(Si3210/Si3210M Only)
The control logic for a pulse-width-modulated (PWM)
dc-dc converter is incorporated in the Si3210. Output
pins DCDRV and DCFF are used to switch a bipolar
transistor or MOSFET. The polarity of DCFF is opposite
that of DCDRV.
The dc-dc converter circuit is powered on when the
DCOF
bit
in
the
Powerdown
Register
(direct
Register 14, bit 4) is cleared to 0. The switching
regulator
circuit
within
the
Si3210
is
a
high-
performance, pulse-width modulation controller. The
control pins are driven by the PWM controller logic in
the Si3210. The regulated output voltage (VBAT) is
sensed by the SVBAT pin and is used to detect whether
the output voltage is above or below an internal
reference for the desired battery voltage. The dc
monitor pins, SDCH and SDCL, monitor input current
and voltage to the dc-dc converter external circuitry. If
an overload condition is detected, the PWM controller
will turn off the switching transistor for the remainder of
a
PWM
period
to
prevent
damage
to
external
components. It is important that the proper value of R18
be selected to ensure safe operation. Guidance is given
in AN45.
The PWM controller operates at a frequency set by the
dc-dc Converter PWM register (direct Register 92).
During a PWM period, the outputs of the control pins,
DCDRV and DCFF, are asserted for a time given by the
read-only
PWM
Pulse
Width
register
(direct
Register 94).
The dc-dc converter must be off for some time in each
cycle to allow the inductor or transformer to transfer its
stored energy to the output capacitor, C9. This minimum
off time can be set through the dc-dc Converter
Switching Delay register, (direct Register 93). The
number of 16.384 MHz clock cycles that the controller is
off is equal to DCTOF (bits 0 through 4) plus 4. If the dc
Monitor pins detect an overload condition, the dc-dc
converter interrupts its conversion cycles regardless of
the register settings to prevent component damage.
These inputs should be calibrated by writing the DCCAL
bit (bit 7) of the dc-dc Converter Switching Delay
register, direct Register 93, after the dc-dc converter
has been turned on.
Because the Si3210 dynamically regulates its own
battery supply voltage using the dc-dc converter
controller, the battery voltage, VBAT, is offset from the
negative-most terminal by a programmable voltage,
VOV, to allow voltage headroom for carrying audio
signals.
As mentioned previously, the Si3210 dynamically
adjusts VBAT to suit the particular circuit requirement. To
illustrate this, the behavior of VBAT in the active state is
shown in Figure 19. In the active state, the TIP-to-RING
open circuit voltage is kept at VOC in the constant
voltage region while the regulator output voltage
VBAT =VCM + VOC + VOV.
When the loop current attempts to exceed ILIM, the dc
line driver circuit enters constant current mode allowing
the TIP to RING voltage to track RLOOP. As the TIP
terminal is kept at a constant voltage, it is the RING
terminal voltage that tracks RLOOP and, as a result, the
|VBAT| voltage will also track RLOOP. In this state,
|VBAT|= ILIM x RLOOP + VCM +VOV. As RLOOP decreases
below the VOC/ILIM mark, the regulator output voltage
can continue to track RLOOP (TRACK = 1), or the RLOOP
tracking mechanism is stopped when |VBAT|= |VBATL|
(TRACK = 0). The former case is the more common
application
and
provides
the
maximum
power
dissipation savings. In principle, the regulator output
voltage can go as low as |VBAT|=VCM+ VOV, offering
significant power savings.
When TRACK = 0, |VBAT| will not decrease below
VBATL. The RING terminal voltage, however, continues
to decrease with decreasing RLOOP.
相关PDF资料 |
PDF描述 |
|---|---|
| VI-2N4-IX-S | CONVERTER MOD DC/DC 48V 75W |
| SI3211-E-GMR | IC PROSLIC/CODEC DTMF 38VQFN |
| SI3216M-C-GM | IC SLIC/CODEC 1CH 38QFN |
| SI3216-C-GM | IC SLIC/CODEC 1CH 38QFN |
| VE-2NT-IX-S | CONVERTER MOD DC/DC 6.5V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SI3210-FTR | 功能描述:电信线路管理 IC Single-CH SLIC/Codec dc-dc RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| SI3210-GT | 功能描述:电信线路管理 IC Single-Channel SLIC Codec RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| SI3210-GTR | 功能描述:电信线路管理 IC Single-CH SLIC/Codec dc-dc RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| SI3210-KT | 功能描述:电信线路管理 IC Single Channel SLIC /CODEC w/DTMF RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| SI3210-KTR | 功能描述:电信线路管理 IC Sgl Ch SLIC/Codec w/ DTMF Decoder RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。