- 您现在的位置：买卖IC网 > PDF目录10997 > SI3210-FT (Silicon Laboratories Inc)IC SLIC/CODEC PROGRAMMBL 38TSSOP PDF资料下载
参数资料
| 型号： | SI3210-FT |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 98/148页 |
| 文件大小： | 0K |
| 描述： | IC SLIC/CODEC PROGRAMMBL 38TSSOP |
| 标准包装： | 50 |
| 系列： | ProSLIC® |
| 功能： | 用户线路接口概念（SLIC），CODEC |
| 接口： | PCM，SPI |
| 电路数： | 1 |
| 电源电压： | 3.3V，5V |
| 电流 - 电源： | 88mA |
| 功率（瓦特）： | 700mW |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 38-TFSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 38-TSSOP |
| 包装： | 管件 |
| 包括： | BORSCHT 功能，DTMF 生成和解码，FSK 生成，脉冲测量生成，语音回送测试模式 |
| 其它名称： | 336-1168 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页当前第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页
Si3210/Si3211
Rev. 1.61
53
Not
Recommended
fo
r N
ew
esi
gn
s
Pulse metering active timer expired
Pulse metering inactive timer expired
Indirect register access complete
The interface to the interrupt logic consists of six registers. Three interrupt status registers contain one bit for each
of the above interrupt functions. These bits will be set when an interrupt is pending for the associated resource.
Three interrupt enable registers also contain one bit for each interrupt function. In the case of the interrupt enable
registers, the bits are active high. Refer to the appropriate functional description section for operational details of
the interrupt functions.
When a resource reaches an interrupt condition, it will signal an interrupt to the interrupt control block. The interrupt
control block will then set the associated bit in the interrupt status register if the enable bit for that interrupt is set.
The INT pin is a NOR of the bits of the interrupt status registers. Therefore, if a bit in the interrupt status registers is
asserted, IRQ will assert low. Upon receiving the interrupt, the interrupt handler should read interrupt status
registers to determine which resource is requesting service. To clear a pending interrupt, write the desired bit in the
appropriate interrupt status register to 1. Writing a 0 has no effect. This provides a mechanism for clearing
individual bits when multiple interrupts occur simultaneously. While the interrupt status registers are non-zero, the
INT pin will remain asserted.
2.11. Serial Peripheral Interface
The control interface to the ProSLIC is a 4-wire interface modeled after commonly-available micro-controller and
serial peripheral devices. The interface consists of a clock (SCLK), chip select (CS), serial data input (SDI), and
serial data output (SDO). Data is transferred a byte at a time with each register access consisting of a pair of byte
The first byte of the pair is the command/address byte. The MSB of this byte indicates a register read when 1 and
a register write when 0. The remaining seven bits of the command/address byte indicate the address of the register
to be accessed. The second byte of the pair is the data byte. Because the falling edge of CS provides
resynchronization of the SPI state machine in the event of a framing error, it is recommended (but not required) that
During a read operation, the SDO becomes active and the 8-bit contents of the register are driven out MSB first.
The SDO will be high impedance on either the falling edge of SCLK following the LSB, or the rising of CS as
specified by the SPIM bit (direct Register 0, bit 6). SDI is a “don’t care” during the data portion of read operations.
During write operations, data is driven into the ProSLIC via the SDI pin MSB first. The SDO pin will remain high
impedance during write operations. Data always transitions with the falling edge of the clock and is latched on the
rising edge. The clock should return to a logic high when no transfer is in progress.
Indirect registers are accessed through direct registers 29 through 30. Instructions on how to access them is
described in “3. Control Registers” beginning on page 60.
There are a number of variations of usage on this four-wire interface:
Continuous Clocking: During continuous clocking, the data transfers are controlled by the assertion of the CS
pin. CS must assert before the falling edge of SCLK on which the first bit of data is expected during a read
cycle, and must remain low for the duration of the 8-‘bit transfer (command/address or data).
SDI/SDO Wired Operation: Independent of the clocking options described, SDI and SDO can be treated as
two separate lines or wired together if the master is capable of tristating its output during the data byte transfer
of a read operation.
Daisy Chain Mode: This mode allows communication with banks of up to eight ProSLIC devices using one
chip select signal. When the SPIDC bit in the SPI Mode Select register is set, data transfer mode changes to a
3-byte operation: a chip select byte, an address/control byte, and a data byte. Using the circuit shown in
Figure 28, a single device may select from the bank of devices by setting the appropriate chip select bit to 1.
Each device uses the LSB of the chip select byte, shifts the data right by one bit, and passes the chip select
byte using the SDITHRU pin to the next device in the chain. Address/control and data bytes are unaltered.
相关PDF资料 |
PDF描述 |
|---|---|
| VI-2N4-IX-S | CONVERTER MOD DC/DC 48V 75W |
| SI3211-E-GMR | IC PROSLIC/CODEC DTMF 38VQFN |
| SI3216M-C-GM | IC SLIC/CODEC 1CH 38QFN |
| SI3216-C-GM | IC SLIC/CODEC 1CH 38QFN |
| VE-2NT-IX-S | CONVERTER MOD DC/DC 6.5V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SI3210-FTR | 功能描述:电信线路管理 IC Single-CH SLIC/Codec dc-dc RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| SI3210-GT | 功能描述:电信线路管理 IC Single-Channel SLIC Codec RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| SI3210-GTR | 功能描述:电信线路管理 IC Single-CH SLIC/Codec dc-dc RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| SI3210-KT | 功能描述:电信线路管理 IC Single Channel SLIC /CODEC w/DTMF RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| SI3210-KTR | 功能描述:电信线路管理 IC Sgl Ch SLIC/Codec w/ DTMF Decoder RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。