- 您现在的位置：买卖IC网 > PDF目录10997 > SI3210-FT (Silicon Laboratories Inc)IC SLIC/CODEC PROGRAMMBL 38TSSOP PDF资料下载
参数资料
| 型号： | SI3210-FT |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 96/148页 |
| 文件大小： | 0K |
| 描述： | IC SLIC/CODEC PROGRAMMBL 38TSSOP |
| 标准包装： | 50 |
| 系列： | ProSLIC® |
| 功能： | 用户线路接口概念（SLIC），CODEC |
| 接口： | PCM，SPI |
| 电路数： | 1 |
| 电源电压： | 3.3V，5V |
| 电流 - 电源： | 88mA |
| 功率（瓦特）： | 700mW |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 38-TFSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 38-TSSOP |
| 包装： | 管件 |
| 包括： | BORSCHT 功能，DTMF 生成和解码，FSK 生成，脉冲测量生成，语音回送测试模式 |
| 其它名称： | 336-1168 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页当前第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页
Si3210/Si3211
Rev. 1.61
51
Not
Recommended
fo
r N
ew
D
esi
gn
s
2.7.2. Receive Path
In the receive path, the optionally-compressed 8-bit
data is first expanded to 16-bit words. The PCMF
register bit can bypass the expansion process, in
which case two 8-bit words are assembled into one 16-
bit word. DACG is the receive path programmable gain
amplifier, which can be programmed from –
dB to
6 dB. An 8 kHz, 16-bit signal is then provided to a D/A
converter. The resulting analog signal is amplified by
the analog receive amplifier, ARX, which is user-
selectable to one of several options: mute, –3.5, 0, or
3.5 dB.
It
is
then
applied
at
the
input
of
the
transconductance amplifier (Gm), which drives the off-
chip current buffer (IBUF).
2.7.3. Audio Characteristics
The dominant source of distortion and noise in both the
transmit and receive paths is the quantization noise
introduced by the -law or the A-law compression
process. Figure 1 on page 6 specifies the minimum
signal-to-noise-and-distortion ratio for either path for a
sine wave input of 200 Hz to 3400 Hz.
Both the -law and the A-law speech encoding allow the
audio codec to transfer and process audio signals larger
than 0 dBm0 without clipping. The maximum PCM code
is generated for a -law encoded sine wave of
3.17 dBm0
or
an
A-law
encoded
sine
wave
of
3.14 dBm0. The ProSLIC overload clipping limits are
driven by the PCM encoding process. Figure 2 on page
6 shows the acceptable limits for the analog-to-analog
fundamental power transfer-function, which bounds the
behavior of ProSLIC.
The transmit path gain distortion versus frequency is
shown in Figure 3 on page 7. The same figure also
presents the minimum required attenuation for any out-
of-band analog signal that may be applied on the line.
Note the presence of a high-pass filter transfer function
that ensures at least 30 dB of attenuation for signals
below 65 Hz. The low-pass filter transfer function that
attenuates signals above 3.4 kHz has to exceed the
requirements specified by the equations in Figure 3 on
page 7 and is implemented as part of the A-to-D
converter.
The receive path transfer function requirement, shown
in Figure 4 on page 8, is very similar to the transmit path
transfer function. The most notable difference is the
absence of the high-pass filter portion. The only other
differences are the maximum 2 dB of attenuation at
200 Hz (as opposed to 3 dB for the transmit path) and
the 28 dB of attenuation for any frequency above
4.6 kHz. The PCM data rate is 8 kHz and, thus, no
frequencies greater than 4 kHz can be digitally encoded
in the data stream.
From this point of view, at frequencies greater than
4 kHz, the plot in Figure 4 should be interpreted as the
maximum allowable magnitude of any spurious signals
that
are
generated
when
a
PCM
data
stream
representing a sine wave signal in the range of 300 Hz
to 3.4 kHz at a level of 0 dBm0 is applied at the digital
input.
The group delay distortion in either path is limited to no
more than the levels indicated in Figure 5 on page 9.
The reference in Figure 5 is the smallest group delay for
a sine wave in the range of 500 Hz to 2500 Hz at
0dBm0.
The block diagram for the voice-band signal processing
paths is shown in Figure 25. Both the receive and
transmit paths employ the optimal combination of
analog
and
digital
signal
processing
to
provide
maximum performance while offering sufficient flexibility
to allow users to optimize for their particular ProSLIC
application. All programmable signal-processing blocks
are indicated symbolically in Figure 25 by a dashed
arrow across them. The two-wire (TIP/RING) voice-
band interface to the ProSLIC is implemented using a
small number of external components. The receive path
interface consists of a unity-gain current buffer, IBUF,
while the transmit path interface is simply an ac
coupling capacitor. Signal paths, although implemented
differentially, are shown as single-ended for simplicity.
2.7.4. Transhybrid Balance
The
ProSLIC
provides
programmable
transhybrid
balance with gain block H. (See Figure 25.) In the ideal
case, where the synthesized SLIC impedance exactly
matches
the
subscriber
loop
impedance,
the
transhybrid balance should be set to subtract a –6 dB
level from the transmit path signal. The transhybrid
balance gain can be adjusted from –2.77 dB to
+4.08 dB
around
the
ideal
setting
of
–6 dB
by
programming the HYBA[2:0] bits of the Hybrid Control
register (direct Register 11). Note that adjusting any of
the analog or digital gain blocks will not require any
modification of the transhybrid balance gain block, as
the transhybrid gain is subtracted from the transmit path
signal prior to any gain adjustment stages. If desired,
the transhybrid balance can also be disabled using the
appropriate register setting.
2.7.5. Loopback Testing
Four loopback test options are available in the ProSLIC:
The full analog loopback (ALM2) tests almost all the
circuitry of both the transmit and receive paths. The
compressed 8-bit word transmit data stream is fed
back serially to the input of the receive path
expander. (See Figure 25.) The signal path starts
with the analog signal at the input of the transmit
相关PDF资料 |
PDF描述 |
|---|---|
| VI-2N4-IX-S | CONVERTER MOD DC/DC 48V 75W |
| SI3211-E-GMR | IC PROSLIC/CODEC DTMF 38VQFN |
| SI3216M-C-GM | IC SLIC/CODEC 1CH 38QFN |
| SI3216-C-GM | IC SLIC/CODEC 1CH 38QFN |
| VE-2NT-IX-S | CONVERTER MOD DC/DC 6.5V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SI3210-FTR | 功能描述:电信线路管理 IC Single-CH SLIC/Codec dc-dc RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| SI3210-GT | 功能描述:电信线路管理 IC Single-Channel SLIC Codec RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| SI3210-GTR | 功能描述:电信线路管理 IC Single-CH SLIC/Codec dc-dc RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| SI3210-KT | 功能描述:电信线路管理 IC Single Channel SLIC /CODEC w/DTMF RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| SI3210-KTR | 功能描述:电信线路管理 IC Sgl Ch SLIC/Codec w/ DTMF Decoder RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。