- 您现在的位置：买卖IC网 > PDF目录10988 > SI3216M-B-GM (Silicon Laboratories Inc)IC SLIC/CODEC 1CH 38QFN PDF资料下载
参数资料
| 型号： | SI3216M-B-GM |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 51/122页 |
| 文件大小： | 0K |
| 描述： | IC SLIC/CODEC 1CH 38QFN |
| 标准包装： | 43 |
| 系列： | ProSLIC® |
| 功能： | 用户线路接口概念（SLIC），CODEC |
| 接口： | GCI，PCM，SPI |
| 电路数： | 1 |
| 电源电压： | 3.13 V ~ 5.25 V |
| 电流 - 电源： | 88mA |
| 功率（瓦特）： | 700mW |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 38-VFQFN 裸露焊盘 |
| 供应商设备封装： | 38-QFN（5x7） |
| 包装： | 管件 |
| 包括： | 音频音调生成，BORSCHT 功能，FSK 生成，振铃和电池电压生成 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页当前第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页
Si3216
34
Rev. 1.0
Not
Recommended
fo
r N
ew
D
esi
gn
s
power supply (number of REN supported).
For this solution, an n-channel power MOSFET (M1)
switches the current flow through a power transformer
T1. T1 is specified in “AN45: Design Guide for the
Si3210/15/16 DC-DC Converter” and includes several
taps on the primary side to facilitate a wide range of
input voltages. The “M” version of the ProSLIC must be
used for the application circuit depicted in Figure 14 on
page 24 because the DCFF pin is used to drive M1
directly and, therefore, must be the same polarity as
DCDRV. DCDRV is not used in this circuit option;
connecting
DCFF
and
DCDRV
together
is
not
recommended.
2.2.4. DC-DC Converter Architecture
The control logic for a pulse-width modulated (PWM)
dc-dc converter is incorporated in the ProSLIC. Output
pins DCDRV and DCFF are used to switch a bipolar
transistor or MOSFET. The polarity of DCFF is opposite
that of DCDRV.
The dc-dc converter circuit is powered on when the
DCOF bit in the powerdown register (direct Register 14,
bit 4) is cleared to 0. The switching regulator circuit
within the ProSLIC is a high-performance, pulse-width
modulation controller. The control pins are driven by the
PWM controller logic in the ProSLIC. The regulated
output voltage (VBAT) is sensed by the SVBAT pin and
used to detect whether the output voltage is above or
below an internal reference for the desired battery
voltage. The dc monitor pins SDCH and SDCL monitor
input current and voltage to the dc-dc converter external
circuitry. If an overload condition is detected, the PWM
controller will turn off the switching transistor for the
remainder of a PWM period to prevent damage to
external components. It is important that the proper
value of R18 be selected to ensure safe operation.
Guidance is given in “AN45: Design Guide for the
Si3210/15/16 DC-DC Converter”.
The PWM controller operates at a frequency set by the
dc-dc Converter PWM register (direct Register 92).
During a PWM period the outputs of the control pins
DCDRV and DCFF are asserted for a time given by the
read-only
PWM
Pulse
Width
register
(direct
Register 94).
The dc-dc converter must be off for some time in each
cycle to allow the inductor or transformer to transfer its
stored energy to the output capacitor, C9. This minimum
off time can be set through the dc-dc Converter
Switching Delay register, (direct Register 93). The
number of 16.384 MHz clock cycles that the controller is
off is equal to DCTOF (bits 0 through 4) plus 4. If the dc
monitor pins detect an overload condition, the dc-dc
converter interrupts its conversion cycles regardless of
the register settings to prevent component damage.
These inputs should be calibrated by writing the DCCAL
bit (bit 7) of the dc-dc Converter Switching Delay
register, direct Register 93, after the dc-dc converter
has been turned on.
Because the ProSLIC dynamically regulates its own
battery supply voltage using the dc-dc converter
controller, the battery voltage (VBAT) is offset from the
negative-most terminal by a programmable voltage
(VOV) to allow voltage headroom for carrying audio
signals.
As mentioned previously, the ProSLIC dynamically
adjusts VBAT to suit the particular circuit requirement. To
illustrate this, the behavior of VBAT in the Active state is
shown in Figure 19. In the Active state, the TIP-to-RING
open circuit voltage is kept at VOC in the constant
voltage region while the regulator output voltage,
VBAT =VCM + VOC + VOV.
When the loop current attempts to exceed ILIM, the dc
line driver circuit enters constant current mode allowing
the TIP to RING voltage to track RLOOP. As the TIP
terminal is kept at a constant voltage, it is the RING
terminal voltage that tracks RLOOP and, as a result, the
|VBAT| voltage will also track RLOOP. In this state,
|VBAT|= ILIM x RLOOP + VCM + VOV. As RLOOP
decreases below the VOC/ILIM mark, the regulator
output
voltage
can
continue
to
track
RLOOP
(TRACK = 1), or the RLOOP tracking mechanism is
stopped
when
|VBAT|=|VBATL| (TRACK = 0). The
former case is the more common application and
provides the maximum power dissipation savings. In
principle, the regulator output voltage can go as low as
|VBAT|= VCM+ VOV, offering significant power savings.
When TRACK = 0, |VBAT| does not decrease below
VBATL. The RING terminal voltage, however, continues
to decrease with decreasing RLOOP. The power
dissipation on the NPN bipolar transistor driving the
RING terminal can become large and may require a
higher power rating device. The non-tracking mode of
operation is required by specific terminal equipment
which, in order to initiate certain data transmission
modes, goes briefly on-hook to measure the line voltage
to determine whether there is any other off-hook
terminal equipment on the same line. TRACK = 0 mode
is desired since the regulator output voltage has long
settling time constants (tens of milliseconds) and cannot
change rapidly for TRACK = 1 mode. Therefore, the
brief
on-hook
voltage
measurement
would
yield
approximately the same voltage as the off-hook line
voltage and would cause the terminal equipment to
incorrectly sense another off-hook terminal.
相关PDF资料 |
PDF描述 |
|---|---|
| SI3216M-B-FM | IC SLIC/CODEC 1CH 38QFN |
| VI-B0N-IY-F2 | CONVERTER MOD DC/DC 18.5V 50W |
| VI-B0N-IY-F1 | CONVERTER MOD DC/DC 18.5V 50W |
| VI-B0L-IY-F4 | CONVERTER MOD DC/DC 28V 50W |
| VI-B0L-IY-F2 | CONVERTER MOD DC/DC 28V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SI3216M-BT | 功能描述:IC SLIC/CODEC 1CH 38TSSOP RoHS:否 类别:集成电路 (IC) >> 接口 - 电信 系列:ProSLIC® 产品培训模块:Lead (SnPb) Finish for COTS 产品变化通告:Product Discontinuation 06/Feb/2012 标准包装:750 系列:* |
| SI3216M-C-FM | 功能描述:电信线路管理 IC Single-Channel Wide- band SLIC/Codec RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| SI3216M-C-FMR | 功能描述:电信线路管理 IC SnglCH WB SLIC/Codec Transformer dc-dc RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| SI3216M-C-GM | 功能描述:电信线路管理 IC Single-Channel Wide- band SLIC/Codec RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| SI3216M-C-GMR | 功能描述:电信线路管理 IC SnglCH WB SLIC/Codec Transformer dc-dc RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。