参数资料
型号: SP6133EB
厂商: Exar Corporation
文件页数: 6/20页
文件大小: 0K
描述: EVAL BOARD FOR SP6133
标准包装: 1
系列: *
THEORY OF OPERATION
IV IN, x
=
IV IN, x = C OUT ? ? V OUT ?
The SP6133 contains two unique control 
features that are very powerful in distributed
applications. First, non-synchronous driver
control is enabled during start up to prohibit
the low side NFET from pulling down the out-
put until the high side NFET has attempted to
turn on. Second, a  00% duty cycle timeout
ensures that the low side NFET is periodically
enhanced during extended periods at  00%
duty cycle. This guarantees the synchronized
refreshing of the BST capacitor during very
large duty ratios.
The SP6 33 also contains a number of valu-
able protection features. A programmable
input UVLO allows a user to set the exact
value at which the conversion voltage is at a
safe point to begin down conversion, and an
internal V CC UVLO ensures that the controller
itself has enough voltage to properly operate.
Other protection features include thermal
shutdown and short-circuit detection. In the
event that either a
thermal, short-circuit, or UVLO fault is de-
tected, the SP6 33 is forced into an idle state
where the output drivers are held off for a
finite period before a re-start is attempted.
Soft Start
“Soft Start” is achieved when a power con-
verter ramps up the output voltage while
controlling the magnitude of the input sup-
ply source current. In a modern step down
converter, ramping up the non-inverting input
of the error amplifier controls soft start. As a 
result, excess source current can be defined 
as the current required to charge the output 
capacitor
C OUT ?  ?V OUT
? TSoft-start
The SP6 33 provides the user with the op-
tion to program the soft start rate by tying
a capacitor from the SS pin to GND. The
selection of this capacitor is based on the
 0μA pull up current present at the SS pin
and the 0.8V reference voltage. Therefore,
the excess current source can be redefined as:
 0μA
(C SS ?0.8V)
Hiccup
Upon the detection of a power, thermal, or
short-circuit fault, the SP6 33 is forced into
an idle state for a minimum of 200ms. The
SS and COMP pins are immediately pulled
low, and the gate drivers are held off for the
duration of the timeout period. Power and
thermal faults have to be removed before a
restart may be attempted, whereas, a short-
circuit fault is internally cleared shortly after
the fault latch is set. Therefore, a restart at-
tempt is guaranteed every 200ms (typical) as
long as the short-circuit condition persists.
A short-circuit detection comparator has
also been included in the SP6 33 to protect
against the accidental short or severe build
up of current at the output of the power con-
verter. This comparator constantly monitors
the  inputs to the error amplifier, and if the 
V FB pin ever falls more than 250mV (typical)
below the voltage reference, a short-circuit
fault is set. Because the SS pin overrides the
internal 0.8V reference during soft start, the
SP6 33 is capable of detecting short-circuit
faults throughout the duration of soft start as
well as in regular operation.
Error Amplifier & Voltage Loop
As stated before, the heart of the SP6 33
voltage error loop is a high performance,
wide bandwidth transconductance amplifier.  
Because  of  the  amplifier ’s  current  limited 
(+ 00μA) transconductance, there are many
ways to compensate the voltage loop or to
control the COMP pin externally. If a simple,
single pole, single zero response is required, 
then compensation can be as simple as
an RC circuit to ground. If a more complex
compensation is required, then the amplifier 
has enough bandwidth (45°C at 4 MHz) 
and enough gain (60 dB) to run Type III
Oct 24-06 Rev L
SP6 33 Synchronous Buck Controller
6
? 2006 Sipex Corporation
相关PDF资料
PDF描述
RGP02-16EHE3/54 DIODE GPP 0.5A 1600V 300NS DO-41
RS-483.3DZ/H2 CONV DC/DC 2W 18-72VIN +/-3.3V
RS-4815DZ/H2 CONV DC/DC 2W 18-72VIN +/-15VOUT
EL7155CSZ-T7 IC PIN DRIVER 40MHZ 3ST 8-SOIC
RGP02-15EHE3/54 DIODE GPP 0.5A 1500V 300NS DO-41
相关代理商/技术参数
参数描述
SP6133ER1 制造商:SIPEX 制造商全称:Sipex Corporation 功能描述:Evaluation Board Manual
SP6133ER1/TR 制造商:SIPEX 制造商全称:Sipex Corporation 功能描述:Synchronous Buck Controller
SP6133ER1-L 功能描述:DC/DC 开关控制器 Synchronous Buck Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK
SP6133ER1-L/TR 功能描述:DC/DC 开关控制器 Synchronous Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK
SP6134 制造商:SIPEX 制造商全称:Sipex Corporation 功能描述:Dual Supply Synchronous Buck Controller