- 您现在的位置：买卖IC网 > PDF目录225220 > SP7800AJS 2-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, PARALLEL ACCESS, PDSO24 PDF资料下载
参数资料
| 型号： | SP7800AJS |
| 元件分类： | ADC |
| 英文描述： | 2-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, PARALLEL ACCESS, PDSO24 |
| 封装： | 0.300 INCH, PLASTIC, SOIC-24 |
| 文件页数： | 9/13页 |
| 文件大小： | 171K |
| 代理商： | SP7800AJS |
SP7800ADS/02
SP7800A 12-Bit 3
s Sampling A/D Converter
Copyright 2000 Sipex Corporation
5
OBSOLETE
-
HIST
ORICAL
REFERENCE
ONL
Y
ing resistors provide industry–standard input ranges
of
±5Vor±10V.The24-pinSP7800Aisavailablein
plastic DIP, and SOIC packages and it operates from
a single +5V supply. The SP7800A is available in
grades specified over the 0
°C to +70°C commercial
temperature ranges.
edge of R/C will enable the output data pins, and
the data from the previous conversion becomes
valid. The falling edge then puts the SP7800A in
a hold mode, and initiates a new conversion.
The SP7800A will begin acquiring a new sample
just prior to BUSY output rising, and will track the
input signal until the next conversion is started.
For use with an 8-bit bus, the data can be read out
in two bytes under the control of HBE. With a
LOW input on HBE, at the end of a conversion, the
8 LSBs of data are loaded into the output drivers D
7
– D
4 and D3–D0. Taking HBE HIGH then loads the
4 MSBs on output drivers D
3–D0, with D7–D4
being forced LOW.
Analog Input Ranges
The SP7800A offers two standard bipolar input
ranges:
±10V and ±5V. If a ±10V range is re-
quired, the analog input signal should be con-
nected to pin 1. A signal requiring a
±5V range
should be connected to pin 2. In either case, the
other pin of the two must be grounded or connected
to the adjustment circuits described in the section
on calibration.
Controlling The SP7800A
The SP7800A can be easily interfaced to most
microprocessor-based and other digital systems. The
microprocessor may take full control of each conver-
sion, or the SP7800A may operate in a stand-alone
mode, controlled only by the R/C input. Full control
consists of initiating the conversion and reading the
output data at user command, transmitting data either
all 12-bits in one parallel word, or in two 8-bit bytes.
The three control inputs (CS, R/C and HBE) are all
TTL/CMOScompatible.Thefunctionsofthecontrol
lines are shown in Table 1.
For stand-alone operation, control of the SP7800A
is accomplished by a single control line connected
to R/C. In this mode, CS and HBE are connected
to GND. The output data are presented as 12-bit
words. The stand-alone mode is used in systems
containing dedicated input ports which do not
require full bus interface capability.
ConversionisinitiatedbyaHIGH-to-LOWtransition
OPERATION...
Basic Operation
Figure 1 shows the simple hookup circuit required
to operate the SP7800A in a
±10V range in the
Convert Mode. A convert command arriving on
R/C, (a pulse taking R/C LOW for a minimum of
40ns) puts the SP7800A in the HOLD mode, and
a conversion is started. The falling edge of R/C
establishes the sampling instant of the A/D; it must
therefore have very low jitter. BUSY will be held
LOW during the conversion, and rises only after
the conversion is completed and the data has been
transferred to the output drivers. Thus, the rising
edge can be used to read the data from the conver-
sion. Also, during conversion, the BUSY signal
puts the output data lines in Hi-Z states and inhibits
the input lines. This means that pulses on R/C are
ignored, so that new conversions cannot be initi-
ated during a conversion, either as a result of
spurious signals or to short-cycle the SP7800A.
In the Read Mode, the input to R/C is kept nor-
mally LOW, and a HIGH pulse is used to read data
and initiate a conversion. In this mode, the rising
Figure 1. Basic
±10V Operation
1
2
3
4
5
6
7
8
9
10
11
12
24
23
22
21
20
19
18
17
16
15
14
13
D0
(LSB)
Busy
Convert
Command
0.1F
6.8F +
+5V
N.C.
BUSY
CS
R/C
HBE
D0 (LSB)
D1
D2
D3
DGND
IN 1
IN 2
N.C.
AGND
D11 (MSB)
D10
D9
D8
D7
D6
D5
D4
D11
(MSB)
Data
Out
Input
相关PDF资料 |
PDF描述 |
|---|---|
| SP7802SQ/883 | 12-BIT SUCCESSIVE APPROXIMATION ADC, PARALLEL ACCESS, CDIP24 |
| SP809EK-L-2-3 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 |
| SP810EK-2.3/TR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 |
| SP8121BS | 8-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, PARALLEL ACCESS, PDSO32 |
| SP813MCN-L | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SP7800AKN | 制造商:SIPEX 制造商全称:Sipex Corporation 功能描述:12-Bit 3ms Sampling A/D Converter |
| SP7800AKS | 制造商:SIPEX 制造商全称:Sipex Corporation 功能描述:12-Bit 3ms Sampling A/D Converter |
| SP7805AIS WAF | 制造商:Texas Instruments 功能描述: |
| SP7805V2-L | 功能描述:DC/DC 开关控制器 30 TERMINAL 1A POS RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| SP7805V2-L/TR | 功能描述:DC/DC 开关控制器 30 TERMINAL 1A POS RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。