参数资料
型号: SPC5200CVR400
厂商: Freescale Semiconductor
文件页数: 31/80页
文件大小: 0K
描述: IC MPU 32BIT 400MHZ 272-PBGA
标准包装: 40
系列: MPC52xx
处理器类型: 32-位 MPC52xx PowerPC
速度: 400MHz
电压: 1.5V
安装类型: 表面贴装
封装/外壳: 272-BBGA
供应商设备封装: 272-PBGA(27x27)
包装: 托盘
Electrical and Thermal Characteristics
MPC5200 Data Sheet, Rev. 4
Freescale Semiconductor
37
(t)LI
015001500150
Limited Interlock time.1,2
A8.34
(t)MLI
20
20
20
Interlock time with minimum.1,2
A8.35
(t)UI
0
0
0
Unlimited interlock time. 1,2
A8.36
(t)AZ
10
10
10
Maximum time allowed for output drivers to release
from being asserted or negated
A8.37
(t)ZAH
20
20
20
Minimum delay time required for output drivers to
assert or negate from released state
A8.38
(t)ZAD
0—0—0—
A8.39
(t)ENV
20
70
20
70
20
70
Envelope time—from DMACK to STOP and
HDMARDY during data out burst initiation.
A8.40
(t)SR
50
30
20
STROBE to DMARDY time, if DMARDY is negated
before this long after STROBE edge, the recipient
receives no more than one additional data word.
A8.41
(t)RFS
75
60
50
Ready-to-Final STROBE time—no STROBE edges
are sent this long after negation of DMARDY.
A8.42
(t)RP
160
125
100
Ready-to-Pause time—the time recipient waits to
initiate pause after negating DMARDY.
A8.43
(t)IORDYZ
20
20
20
Pull-up time before allowing IORDY to be released.
A8.44
(t)ZIORDY
0
0
0
Minimum time drive waits before driving IORDY
A8.45
(t)ACK
20
20
20
Setup and hold times for DMACK, before assertion or
negation.
A8.46
(t)SS
50
50
50
Time from STROBE edge to negation of DMARQ or
assertion of STOP, when sender terminates a burst.
A8.47
NOTES:
1
tUI, tMLI, tLI indicate sender-to-recipient or recipient-to-sender interlocks. That is, one agent (either sender or recipient)
is waiting for the other agent to respond with a signal before proceeding.
tUI is an unlimited interlock that has no maximum time value.
tMLI is a limited time-out that has a defined minimum.
tLI is a limited time-out that has a defined maximum.
2
All timing parameters are measured at the connector of the drive to which the parameter applies. For example, the
sender shall stop generating STROBE edges tRFS after negation of DMARDY. Both STROBE and DMARDY timing
measurements are taken at the connector of the sender. Even though the sender stops generating STROBE edges,
the receiver may receive additional STROBE edges due to propagation delays. All timing measurement switching
points (low to high and high to low) are taken at 1.5 V.
Table 29. Ultra DMA Timing Specification (continued)
Name
MODE 0
(ns)
MODE 1
(ns)
MODE 2
(ns)
Comment
SpecID
Min
Max
Min
Max
Min
Max
相关PDF资料
PDF描述
SPC5517GAMMG66 IC MCU 32B 1.5MB FLASH 208MAPBGA
SPC5604PGF0MLQ6 IC MCU 32BIT 512KB FLASH 144LQFP
SST89C58RC-40-C-QIF IC MCU 8BIT FLASH 40WQFN
SST89E54RC-33-C-PIE IC MCU 8BIT 17KB FLASH 40PDIP
SST89E58RD2-40-I-TQJE IC MCU 8BIT FLASH 44TQFP
相关代理商/技术参数
参数描述
SPC5200CVR400B 功能描述:微处理器 - MPU HABANERO AUTO PBFREE RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324
SPC5200CVR400BR2 功能描述:微处理器 - MPU HABANERO AUTO PB FREE RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324
SPC5200CVR400R2 功能描述:IC MPU 32BIT 400MHZ 272-PBGA RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微处理器 系列:MPC52xx 标准包装:2 系列:MPC8xx 处理器类型:32-位 MPC8xx PowerQUICC 特点:- 速度:133MHz 电压:3.3V 安装类型:表面贴装 封装/外壳:357-BBGA 供应商设备封装:357-PBGA(25x25) 包装:托盘
SPC5200VVR266B 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:SDRAM/DDR Memory Controller
SPC5293 制造商:SPC Multicomp 功能描述:D Subminiature Gender Changer Convert Fr