- 您现在的位置：买卖IC网 > PDF目录4386 > SST25VF016B-50-4I-QAF (Microchip Technology)IC FLASH SER 16M 50MHZ SPI 8WSON PDF资料下载
参数资料
| 型号： | SST25VF016B-50-4I-QAF |
| 厂商： | Microchip Technology |
| 文件页数： | 12/32页 |
| 文件大小： | 0K |
| 描述： | IC FLASH SER 16M 50MHZ SPI 8WSON |
| 标准包装： | 98 |
| 系列： | SST25 |
| 格式 - 存储器： | 闪存 |
| 存储器类型： | FLASH |
| 存储容量： | 16M（2M x 8） |
| 速度： | 50MHz |
| 接口： | SPI 串行 |
| 电源电压： | 2.7 V ~ 3.6 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 8-WSON |
| 供应商设备封装： | 8-WSON |
| 包装： | 管件 |
| 产品目录页面： | 1452 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页当前第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
16 Mbit SPI Serial Flash
A Microchip Technology Company
SST25VF016B
Data Sheet
Auto Address Increment (AAI) Word-Program
The AAI program instruction allows multiple bytes of data to be programmed without re-issuing the
next sequential address location. This feature decreases total programming time when multiple bytes
or entire memory array is to be programmed. An AAI Word program instruction pointing to a protected
memory area will be ignored. The selected address range must be in the erased state (FFH) when ini-
tiating an AAI Word Program operation. While within AAI Word Programming sequence, only the fol-
lowing instructions are valid: for software end-of-write detection—AAI Word (ADH), WRDI (04H), and
RDSR (05H); for hardware end-of-write detection—AAI Word (ADH) and WRDI (04H). There are three
options to determine the completion of each AAI Word program cycle: hardware detection by reading
the Serial Output, software detection by polling the BUSY bit in the software status register, or wait T BP.
Refer to“End-of-Write Detection” for details.
Prior to any write operation, the Write-Enable (WREN) instruction must be executed. Initiate the AAI
Word Program instruction by executing an 8-bit command, ADH, followed by address bits [A 23 -A 0 ]. Fol-
lowing the addresses, two bytes of data are input sequentially, each one from MSB (Bit 7) to LSB (Bit
0). The first byte of data (D0) is programmed into the initial address [A 23 -A 1 ] with A 0 =0, the second
byte of Data (D1) is programmed into the initial address [A 23 -A 1 ] with A 0 =1. CE# must be driven high
before executing the AAI Word Program instruction. Check the BUSY status before entering the next
valid command. Once the device indicates it is no longer busy, data for the next two sequential
addresses may be programmed, followed by the next two, and so on.
When programming the last desired word, or the highest unprotected memory address, check the busy
status using either the hardware or software (RDSR instruction) method to check for program comple-
tion. Once programming is complete, use the applicable method to terminate AAI. If the device is in
Software End-of-Write Detection mode, execute the Write-Disable (WRDI) instruction, 04H. If the
device is in AAI Hardware End-of-Write Detection mode, execute the Write-Disable (WRDI) instruction,
04H, followed by the 8-bit DBSY command, 80H. There is no wrap mode during AAI programming
once the highest unprotected memory address is reached. See Figures 10 and 11 for the AAI Word
programming sequence.
End-of-Write Detection
There are three methods to determine completion of a program cycle during AAI Word programming:
hardware detection by reading the Serial Output, software detection by polling the BUSY bit in the Soft-
ware Status Register, or wait T BP. The Hardware End-of-Write detection method is described in the
section below.
Hardware End-of-Write Detection
The Hardware End-of-Write detection method eliminates the overhead of polling the Busy bit in the
Software Status Register during an AAI Word program operation. The 8-bit command, 70H, configures
the Serial Output (SO) pin to indicate Flash Busy status during AAI Word programming. (see Figure 8)
The 8-bit command, 70H, must be executed prior to initiating an AAI Word-Program instruction. Once
an internal programming operation begins, asserting CE# will immediately drive the status of the inter-
nal flash status on the SO pin. A ‘0’ indicates the device is busy and a ‘1’ indicates the device is ready
for the next instruction. De-asserting CE# will return the SO pin to tri-state. While in AAI and Hardware
End-of-Write detection mode, the only valid instructions are AAI Word (ADH) and WRDI (04H).
To exit AAI Hardware End-of-Write detection, first execute WRDI instruction, 04H, to reset the Write-
Enable-Latch bit (WEL=0) and AAI bit. Then execute the 8-bit DBSY command, 80H, to disable RY/
BY# status during the AAI command. See Figures 9 and 10.
?2011 Silicon Storage Technology, Inc.
12
DS25044A
08/11
相关PDF资料 |
PDF描述 |
|---|---|
| ACC43DRYS-S734 | CONN EDGECARD 86POS DIP .100 SLD |
| RBB106DHBS-S621 | EDGECARD 212POS DIP R/A .050 SLD |
| FMC20DRYI | CONN EDGECARD 40POS DIP .100 SLD |
| HMC40DRYS-S93 | CONN EDGECARD 80POS DIP .100 SLD |
| FMC22DRXN-S734 | CONN EDGECARD 44POS DIP .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SST25VF016B-50-4I-QAF OLD SST P/N | 功能描述:闪存 16M (2Mx8) 50MHz 2.7-3.6V Industrial RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel |
| SST25VF016B-50-4I-QAF-T | 功能描述:闪存 2.7V to 3.6V 16Mbit SPI Serial 闪存 RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel |
| SST25VF016B-50-4I-QAF-T_ | 制造商:Microchip Technology Inc 功能描述: |
| SST25VF016B-50-4I-S2A | 制造商:Microchip Technology Inc 功能描述:Flash Memory 16 Mbit 50 MHz 8-SOIC |
| SST25VF016B-50-4I-S2AF | 功能描述:闪存 16Mbit 50MHz RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。