参数资料
| 型号： | ST16C554DCJ68-F |
| 厂商： | Exar Corporation |
| 文件页数： | 34/39页 |
| 文件大小： | 0K |
| 描述： | IC UART FIFO 16B QUAD 68PLCC |
| 标准包装： | 19 |
| 特点： | * |
| 通道数： | 4，QUART |
| FIFO's： | 16 字节 |
| 规程： | RS232 |
| 电源电压： | 2.97 V ~ 5.5 V |
| 带自动流量控制功能： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 68-LCC（J 形引线） |
| 供应商设备封装： | 68-PLCC |
| 包装： | 管件 |
| 其它名称： | 1016-1265-5 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页当前第34页第35页第36页第37页第38页第39页
ST16C554/554D
4
2.97V TO 5.5V QUAD UART WITH 16-BYTE FIFO
REV. 4.0.1
INTA
(IRQ#)
6
15
O
(OD)
When 16/68# pin is HIGH for Intel bus interface, this ouput becomes channel A
interrupt output. The output state is defined by the user and through the soft-
ware setting of MCR[3]. INTA is set to the active mode when MCR[3] is set to a
logic 1. INTA is set to the three state mode when MCR[3] is set to a logic 0
(default). See MCR[3].
When 16/68# pin is LOW for Motorola bus interface, this output becomes device
interrupt output (active low, open drain). An external pull-up resistor is required
for proper operation.
INTB
INTC
INTD
(N.C.)
12
37
43
21
49
55
O
When 16/68# pin is HIGH for Intel bus interface, these ouputs become the inter-
rupt outputs for channels B, C, and D. The output state is defined by the user
through the software setting of MCR[3]. The interrupt outputs are set to the
active mode when MCR[3] is set to a logic 1 and are set to the three state mode
when MCR[3] is set to a logic 0 (default). See MCR[3].
When 16/68# pin is LOW for Motorola bus interface, these outputs are unused
and will stay at logic zero level. Leave these outputs unconnected.
INTSEL
-
65
I
Interrupt Select (active high, input with internal pull-down).
When 16/68# pin is HIGH for Intel bus interface, this pin can be used in conjunc-
tion with MCR bit-3 to enable or disable the INT A-D pins or override MCR bit-3
and enable the interrupt outputs. Interrupt outputs are enabled continuously
when this pin is HIGH. MCR bit-3 enables and disables the interrupt output
pins. In this mode, MCR bit-3 is set to a logic 1 to enable the continuous output.
See MCR bit-3 description for full detail. This pin must be LOW in the Motorola
bus interface mode. For the 64 pin packages, this pin is bonded to VCC inter-
nally in the ST16C554DCQ64 so the INT outputs operate in the continuous
interrupt mode. This pin is bonded to GND internally in the ST16C554CQ64 and
therefore requires setting MCR bit-3 for enabling the interrupt output pins.
TXRDY#
-
39
O
Transmitter Ready (active low). This output is a logically ANDed status of
TXRDY# A-D. See Table 5. If this output is unused, leave it unconnected.
RXRDY#
-
38
O
Receiver Ready (active low). This output is a logically ANDed status of RXRDY#
A-D. See Table 5. If this output is unused, leave it unconnected.
MODEM OR SERIAL I/O INTERFACE
TXA
TXB
TXC
TXD
8
10
39
41
17
19
51
53
O
UART channels A-D Transmit Data and infrared transmit data. In this mode, the
TX signal will be HIGH during reset, or idle (no data).
RXA
RXB
RXC
RXD
62
20
29
51
7
29
41
63
I
UART channel A-D Receive Data. Normal receive data input must idle HIGH.
RTSA#
RTSB#
RTSC#
RTSD#
5
13
36
44
14
22
48
56
O
UART channels A-D Request-to-Send (active low) or general purpose output. If
these outputs are not used, leave them unconnected.
CTSA#
CTSB#
CTSC#
CTSD#
2
16
33
47
11
25
45
59
I
UART channels A-D Clear-to-Send (active low) or general purpose input. These
inputs should be connected to VCC when not used.
Pin Description
NAME
64-LQFP
PIN #
68-PLCC
PIN#
TYPE
DESCRIPTION
相关PDF资料 |
PDF描述 |
|---|---|
| XR16V554IL-F | IC UART FIFO 16B QUAD 48QFN |
| XR16L2751IM-F | IC UART FIFO 64B DUAL 48TQFP |
| XR16L2751CM-F | IC UART FIFO 64B DUAL 48TQFP |
| MAX7311AAG+ | IC I/O EXPANDER I2C 16B 24SSOP |
| XR16C850IM-F | IC UART FIFO 128B 48TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ST16C554DCJ68TR | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
| ST16C554DCJ68TR-F | 功能描述:UART 接口集成电路 QUAD UART W/16 BYTE FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| ST16C554DCQ-0A-EB | 功能描述:界面开发工具 Supports C554D 64 ld TQFP, ISA Interface RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| ST16C554DCQ64 | 制造商:Exar Corporation 功能描述: |
| ST16C554DCQ64F | 制造商:Exar Corporation 功能描述: |
发布紧急采购，3分钟左右您将得到回复。