参数资料
型号: ST72622L2T1
厂商: STMICROELECTRONICS
元件分类: 微控制器/微处理器
英文描述: 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP44
封装: TQFP-44
文件页数: 85/134页
文件大小: 815K
代理商: ST72622L2T1
ST7262
54/134
10.4 SERIAL PERIPHERAL INTERFACE (SPI)
10.4.1 Introduction
The Serial Peripheral Interface (SPI) allows full-
duplex, synchronous, serial communication with
external devices. An SPI system may consist of a
master and one or more slaves or a system in
which devices may be either masters or slaves.
The SPI is normally used for communication be-
tween the microcontroller and external peripherals
or another microcontroller.
Refer to the Pin Description chapter for the device-
specific pin-out.
10.4.2 Main Features
s
Full duplex, three-wire synchronous transfers
s
Simplex, two wire synchronous transfers
s
Master or slave operation selectable either
through software or hardware
s
Six master mode frequencies
s
Maximum slave mode frequency = fCPU/2.
s
Programmable clock polarity and phase
s
End of transfer interrupt flag
s
Write collision flag protection
s
Master mode fault protection capability.
s
Overrun error detection flag.
10.4.3 General Description
The SPI is connected to external devices through
4(3) alternate pins:
– MISO: Master In / Slave Out pin
– MOSI: Master Out / Slave In pin
– SCK: Serial Clock pin
– SS: Slave select pin (if not done through soft-
ware)
A basic example of interconnections between a
single master and a single slave is illustrated on
Figure 1.
The MOSI pins are connected together as are
MISO pins. In this way data is transferred serially
between master and slave (most significant bit
first).
When the master device transmits data to a slave
device via MOSI pin, the slave device responds by
sending data to the master device via the MISO
pin. This implies full duplex transmission with both
data out and data in synchronized with the same
clock signal (which is provided by the master de-
vice via the SCK pin).
Thus, the byte transmitted is replaced by the byte
received and eliminates the need for separate
transmit-empty and receiver-full bits. A status flag
is used to indicate that the I/O operation is com-
plete.
Four possible data/clock timing relationships may
be chosen (see Figure 4) but master and slave
must be programmed with the same timing mode.
Figure 36. Serial Peripheral Interface Master/Slave
8-BIT SHIFT REGISTER
SPI
CLOCK
GENERATOR
8-BIT SHIFT REGISTER
MISO
MOSI
MISO
SCK
SLAVE
MASTER
SS
+5V
MSBit
LSBit
MSBit
LSBit
1
相关PDF资料
PDF描述
ST72621L4T1 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP44
ST72632K2B1/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP32
ST72E631K4D0 8-BIT, UVPROM, 8 MHz, MICROCONTROLLER, PDIP32
ST72633K1M1/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO34
ST7263BK1M1/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO34
相关代理商/技术参数
参数描述
ST7263-EMU2 功能描述:仿真器/模拟器 ST7 Emulator Board RoHS:否 制造商:Blackhawk 产品:System Trace Emulators 工具用于评估:C6000, C5000, C2000, OMAP, DAVINCI, SITARA, TMS470, TMS570, ARM 7/9, ARM Cortex A8/R4/M3 用于:XDS560v2
ST7265X-EVAL/MS 制造商:STMicroelectronics 功能描述:ST6 EVAL BD - Bulk
ST7265X-EVAL/PFD 制造商:STMicroelectronics 功能描述:USB FLASH EVAL - Bulk
ST7266 制造商:6940 功能描述:ST7266
ST7267C8T1L 制造商:STMicroelectronics 功能描述: