参数资料
型号: ST7PLU09MAE
厂商: STMICROELECTRONICS
元件分类: 微控制器/微处理器
英文描述: 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO8
封装: 0.150 INCH, ROHS COMPLIANT, PLASTIC, SOP-8
文件页数: 100/124页
文件大小: 1995K
代理商: ST7PLU09MAE
ST7LUS5, ST7LU05, ST7LU09
On-chip peripherals
RAIN is the maximum recommended impedance for an analog input signal. If the impedance
is too high, this will result in a loss of accuracy due to leakage and sampling not being
completed in the allocated time.
A/D conversion phases
The A/D conversion is based on two conversion phases:
Sample capacitor loading [duration: tSAMPLE]
During this phase, the VAIN input voltage to be measured is loaded into the CADC
sample capacitor.
A/D conversion [duration: tHOLD]
During this phase, the A/D conversion is computed (8 successive approximations
cycles) and the CADC sample capacitor is disconnected from the analog input pin to get
the optimum analog to digital conversion accuracy.
The total conversion time: tCONV = tSAMPLE + tHOLD
While the ADC is on, these two phases are continuously repeated.
At the end of each conversion, the sample capacitor is kept loaded with the previous
measurement load. The advantage of this behavior is that it minimizes the current
consumption on the analog pin in case of single input channel measurement.
A/D conversion
The analog input ports must be configured as input, no pull-up, no interrupt. Refer to the “I/O
ports” chapter. Using these pins as analog inputs does not affect the ability of the port to be
read as a logic input.
In the ADCCSR register:
Select the CS[2:0] bits to assign the analog channel to convert.
ADC conversion mode
In the ADCCSR register:
Set the ADON bit to enable the A/D converter and to start the conversion. From this
time on, the ADC performs a continuous conversion of the selected channel.
When a conversion is complete:
The EOC bit is set by hardware.
The result is in the ADCDR registers.
A read to the ADCDRH resets the EOC bit.
To read the 10 bits, perform the following steps:
1.
Poll EOC bit
2.
Read ADCDRL
3.
Read ADCDRH. This clears EOC automatically.
To read only 8 bits, perform the following steps:
1.
Poll EOC bit
2.
Read ADCDRH. This clears EOC automatically.
相关PDF资料
PDF描述
ST90135M5T6 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP80
ST90T158M9Q6 16-BIT, OTPROM, 24 MHz, MICROCONTROLLER, PQFP80
ST90158M9Q6 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP80
ST9020B6/XX 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PDIP40
ST9027B6/XX 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PDIP40
相关代理商/技术参数
参数描述
ST7PMC1K2B3 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-bit MCU with nested interrupts, Flash, 10-bit ADC, brushless motor control, five timers, SPI, LINSCI?
ST7PMC1K2B6 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-BIT MCU WITH NESTED INTERRUPTS, FLASH, 10-BIT ADC, BRUSHLESS MOTOR CONTROL, FIVE TIMERS, SPI, LINSCI
ST7PMC1K2T3 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-bit MCU with nested interrupts, Flash, 10-bit ADC, brushless motor control, five timers, SPI, LINSCI?
ST7PMC1K2T6 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-BIT MCU WITH NESTED INTERRUPTS, FLASH, 10-BIT ADC, BRUSHLESS MOTOR CONTROL, FIVE TIMERS, SPI, LINSCI
ST7PMC1K2T6/ST7PMC1K2 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-BIT MCU WITH NESTED INTERRUPTS, FLASH, 10-BIT ADC, BRUSHLESS MOTOR CONTROL, FIVE TIMERS, SPI, LINSCI