参数资料
型号: ST7PLU09MCTRE
厂商: STMICROELECTRONICS
元件分类: 微控制器/微处理器
英文描述: 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO8
封装: 0.150 INCH, ROHS COMPLIANT, PLASTIC, SOP-8
文件页数: 35/124页
文件大小: 1995K
代理商: ST7PLU09MCTRE
Flash program memory
ST7LUS5, ST7LU05, ST7LU09
4
Flash program memory
4.1
Introduction
The ST7 single voltage extended Flash (XFlash) is a non-volatile memory that can be
electrically erased and programmed either on a byte-by-byte basis or up to 32 bytes in
parallel.
The XFlash devices can be programmed off-board (plugged in a programming tool) or on-
board using in-circuit programming or in-application programming.
The array matrix organization allows each sector to be erased and reprogrammed without
affecting other sectors.
4.2
Main features
ICP (in-circuit programming)
IAP (in-application programming)
ICT (in-circuit testing) for downloading and executing user application test patterns in
RAM
Sector 0 size configurable by option byte
Readout and write protection
4.3
Programming modes
The ST7 can be programmed in three different ways:
Insertion in a programming tool - In this mode, Flash sectors 0 and 1 and option byte
row can be programmed or erased.
In-circuit programming - In this mode, Flash sectors 0 and 1 and option byte row can be
programmed or erased without removing the device from the application board.
In-application programming - In this mode, sector 1 can be programmed or erased
without removing the device from the application board and while the application is
running.
4.3.1
In-circuit programming (ICP)
ICP uses a protocol called ICC (in-circuit communication) which allows an ST7 plugged on a
printed circuit board (PCB) to communicate with an external programming device connected
via cable. ICP is performed in three steps:
1.
Switch the ST7 to ICC mode (in-circuit communications). This is done by driving a
specific signal sequence on the ICCCLK/DATA pins while the RESET pin is pulled low.
When the ST7 enters ICC mode, it fetches a specific RESET vector which points to the
ST7 System Memory containing the ICC protocol routine. This routine enables the ST7
to receive bytes from the ICC interface.
2.
Download ICP driver code in RAM from the ICCDATA pin
3.
Execute ICP driver code in RAM to program the Flash memory
相关PDF资料
PDF描述
ST7PLU05MAE 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO8
ST7PLU09MAE 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO8
ST90135M5T6 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP80
ST90T158M9Q6 16-BIT, OTPROM, 24 MHz, MICROCONTROLLER, PQFP80
ST90158M9Q6 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP80
相关代理商/技术参数
参数描述
ST7PMC1K2B3 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-bit MCU with nested interrupts, Flash, 10-bit ADC, brushless motor control, five timers, SPI, LINSCI?
ST7PMC1K2B6 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-BIT MCU WITH NESTED INTERRUPTS, FLASH, 10-BIT ADC, BRUSHLESS MOTOR CONTROL, FIVE TIMERS, SPI, LINSCI
ST7PMC1K2T3 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-bit MCU with nested interrupts, Flash, 10-bit ADC, brushless motor control, five timers, SPI, LINSCI?
ST7PMC1K2T6 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-BIT MCU WITH NESTED INTERRUPTS, FLASH, 10-BIT ADC, BRUSHLESS MOTOR CONTROL, FIVE TIMERS, SPI, LINSCI
ST7PMC1K2T6/ST7PMC1K2 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-BIT MCU WITH NESTED INTERRUPTS, FLASH, 10-BIT ADC, BRUSHLESS MOTOR CONTROL, FIVE TIMERS, SPI, LINSCI