- 您现在的位置：买卖IC网 > PDF目录98146 > ST7PLU09MCTRE (STMICROELECTRONICS) 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO8 PDF资料下载
参数资料
| 型号： | ST7PLU09MCTRE |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO8 |
| 封装： | 0.150 INCH, ROHS COMPLIANT, PLASTIC, SOP-8 |
| 文件页数： | 36/124页 |
| 文件大小： | 1995K |
| 代理商： | ST7PLU09MCTRE |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页当前第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页
ST7LUS5, ST7LU05, ST7LU09
Flash program memory
19/124
Depending on the ICP driver code downloaded in RAM, Flash memory programming can be
fully customized (number of bytes to program, program locations, or selection of the serial
communication interface for downloading).
4.3.2
In-application programming (IAP)
This mode uses an IAP driver program previously programmed in Sector 0 by the user (in
ICP mode).
This mode is fully controlled by user software. This allows it to be adapted to the user
application (user-defined strategy for entering programming mode or choice of
communications protocol used to fetch the data to be stored, etc.).
IAP mode can be used to program any memory areas except Sector 0, which is write/erase
protected to allow recovery in case errors occur during the programming operation.
4.4
ICC interface
ICP needs a minimum of 4 and up to 6 pins to be connected to the programming tool. These
pins are:
●
RESET:
device reset
●
VSS:
device power supply ground
●
ICCCLK:
ICC output serial clock pin(a)
●
ICCDATA: ICC input serial data pin
●
CLKIN:
main clock input for external source
●
VDD:
application board power supply(b)
a.
If the ICCCLK or ICCDATA pins are only used as outputs in the application, no signal isolation is necessary. As
soon as the programming tool is plugged to the board, even if an ICC session is not in progress, the ICCCLK
and ICCDATA pins are not available for the application. If they are used as inputs by the application, isolation
such as a serial resistor has to be implemented in case another device forces the signal. Refer to the
programming tool documentation for recommended resistor values.
b.
The use of Pin 7 of the ICC connector depends on the programming tool architecture. This pin must be
connected when using most ST programming tools (it is used to monitor the application power supply). Please
refer to the programming tool manual.
相关PDF资料 |
PDF描述 |
|---|---|
| ST7PLU05MAE | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO8 |
| ST7PLU09MAE | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO8 |
| ST90135M5T6 | 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP80 |
| ST90T158M9Q6 | 16-BIT, OTPROM, 24 MHz, MICROCONTROLLER, PQFP80 |
| ST90158M9Q6 | 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP80 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ST7PMC1K2B3 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-bit MCU with nested interrupts, Flash, 10-bit ADC, brushless motor control, five timers, SPI, LINSCI? |
| ST7PMC1K2B6 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-BIT MCU WITH NESTED INTERRUPTS, FLASH, 10-BIT ADC, BRUSHLESS MOTOR CONTROL, FIVE TIMERS, SPI, LINSCI |
| ST7PMC1K2T3 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-bit MCU with nested interrupts, Flash, 10-bit ADC, brushless motor control, five timers, SPI, LINSCI? |
| ST7PMC1K2T6 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-BIT MCU WITH NESTED INTERRUPTS, FLASH, 10-BIT ADC, BRUSHLESS MOTOR CONTROL, FIVE TIMERS, SPI, LINSCI |
| ST7PMC1K2T6/ST7PMC1K2 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-BIT MCU WITH NESTED INTERRUPTS, FLASH, 10-BIT ADC, BRUSHLESS MOTOR CONTROL, FIVE TIMERS, SPI, LINSCI |
发布紧急采购，3分钟左右您将得到回复。