- 您现在的位置：买卖IC网 > PDF目录98164 > TAS5518PAGR (TEXAS INSTRUMENTS INC) SPECIALTY CONSUMER CIRCUIT, PQFP64 PDF资料下载
参数资料
| 型号： | TAS5518PAGR |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 消费家电 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PQFP64 |
| 封装： | GREEN, PLASTIC, TQFP-64 |
| 文件页数： | 44/105页 |
| 文件大小： | 1514K |
| 代理商： | TAS5518PAGR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页当前第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页
TAS5518 Controls and Status
35
SLES115 — August 2004
TAS5518
CONTROL
SETTING
Bass filter sets
Filter Set 3
Loudness (5508)
Loudness disabled, default values
AM interference enable
Disabled
AM interference IF
455
AM interference select sequence
1
Tuned freq and mode
0000 , BCD
Subwoofer PSVC control
Enabled
PSVC and PSVC range
Disabled / 0 dB
After the initialization time, the TAS5518 starts the transition to the operational state with the Master volume
set at mute.
Since the TAS5518 has an external crystal time base, following the release of RESET, the TAS5518 sets the
MCLK and data rates and perform the initialization sequences. The PWM outputs are held at a mute state until
the master volume is set to a value other than mute via I2C.
2.2.2 Power Down (PDN)
TheTAS5518 can be placed into the power down mode by holding the PDN terminal low. When power down
mode is entered, both the PLL and the oscillator are shut down. Volume is immediately set to full attenuation
(there is no ramp down). This control uses the PWM mute sequence that provides a low click and pop transition
to the hard mute state (M). A detailed description of the PWM mute sequence is contained in the PWM section.
Power down is an asynchronous operation that does not require MCLK to go into the power down state. To
initiate the power-up sequence requires MCLK to be operational and the TAS5518 to receive 5 MCLKs prior
to the release of PDN.
As long as the PDN terminal is held low the device is in the power down state with the PWM outputs in a hard
mute (M) state. During power down, all I2C and serial data bus operations are ignored. Table 23 shows the
device output signals while PDN is active.
Table 23. Device Outputs During Power Down
SIGNAL
SIGNAL STATE
Valid
Low
PWM P-outputs
M-state = low
PWM M-outputs
M-state = low
SDA
Signal input
PSVC
M-state = low
Following the application of PDN, the TAS5518 does not perform a quiet shutdown to prevent clicks and pops
produced during the application (the leading edge) of this command. The application of PDN immediately
performs a PWM stop. A quiet stop sequence can be performed by first applying MUTE before PDN.
When PDN is released, the system goes to the end state specified by MUTE and BKND_ERR pins and the
I2C register settings.
The crystal time base allows the TAS5518 to determine the CLK rates. Once these rates are determined, the
TAS5518 unmutes the audio.
2.2.3 Backend Error (BKND_ERR)
Backend error is used to provide error management for backend error conditions. Backend error is a level
sensitive signal. Backend error can be initiated by bringing the BKND_ERR terminal low for a minimum 5
MCLK cycles. When BKND_ERR is brought low, the PWM sets either six or eight channels into the PWM
backend error state. This state is described in the PWM section. Once the backend error sequence is initiated,
a delay of 5 ms is performed before the system starts the output reinitialization sequence. After the
initialization time, the TAS5518 begins normal operation. Backend error does not affect other PWM modulator
operations
相关PDF资料 |
PDF描述 |
|---|---|
| TAS5518PAGG4 | SPECIALTY CONSUMER CIRCUIT, PQFP64 |
| TAS5601DCAG4 | 20 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO56 |
| TAS5601DCARG4 | 20 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO56 |
| TAS5601DCAR | 20 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO56 |
| TAS5601DCA | 20 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO56 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TAS5518PAGRG4 | 功能描述:音频 DSP 8 Ch Digital Audio PWM Processor RoHS:否 制造商:Texas Instruments 工作电源电压: 电源电流: 工作温度范围: 安装风格: 封装 / 箱体: 封装:Tube |
| TAS5538 | 制造商:TI 制造商全称:Texas Instruments 功能描述:TAS5612L-TAS5614LDDVEVM |
| TAS5538DGG | 制造商:TI 制造商全称:Texas Instruments 功能描述:TAS5612L-TAS5614LDDVEVM |
| TAS5538DGGR | 制造商:Texas Instruments 功能描述:audio processor |
| TAS5548 | 制造商:TI 制造商全称:Texas Instruments 功能描述:8-Channel HD Compatible Audio Processor with ASRC and PWM Output |
发布紧急采购，3分钟左右您将得到回复。