- 您现在的位置：买卖IC网 > PDF目录85414 > TDA8374A/N3 (NXP SEMICONDUCTORS) SPECIALTY CONSUMER CIRCUIT, PDIP56 PDF资料下载
参数资料
| 型号： | TDA8374A/N3 |
| 厂商： | NXP SEMICONDUCTORS |
| 元件分类： | 消费家电 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PDIP56 |
| 封装： | 0.600 INCH, PLASTIC, SOT-400, SDIP-56 |
| 文件页数： | 36/75页 |
| 文件大小： | 522K |
| 代理商： | TDA8374A/N3 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页当前第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页
1997 Jul 01
41
Philips Semiconductors
Preliminary specication
I2C-bus controlled economy PAL/NTSC
and NTSC TV-processors
TDA837x family
7. Measured in accordance with the test line given in Fig.14. For the differential phase test the peak white setting is
reduced to 87%.
a) The differential gain is expressed as a percentage of the difference in peak amplitudes between the largest and
smallest value relative to the subcarrier amplitude at blanking level.
b) The phase difference is defined as the difference in degrees between the largest and smallest phase angle.
8. This figure is valid for the complete video signal amplitude (peak white-to-black), see Fig.15.
9. The noise inverter is only active in the ‘strong signal mode’ (no noise detected in the incoming signal).
10. The test set-up and input conditions are given in Fig.16. The figures are measured with an input signal of
10 mV (RMS).
11. Measured with a source impedance of 75
, where:
12. The AGC response time is also dependent on the acquisition time of the PLL demodulator. The values given are valid
when the PLL is in lock.
13. The AFC control voltage is obtained from the control voltage of the VCO of the PLL demodulator. The tuning
information is supplied to the tuning system via the I2C-bus. Two bits are reserved for this function. The AFC value
is valid only when the SL bit = 1.
14. Vi = 100 mV (RMS), FM: 1 kHz, f= ±50 kHz.
15. Vi = 50 mV (RMS), f = 4.5 to 5.5 MHz; FM: 70 Hz, ±50 kHz deviation; AM: 1 kHz, 30% modulation.
16. The Automatic Volume Levelling (AVL) circuit automatically stabilizes the audio output signal to a certain level which
can be set by means of the volume control. This AVL function prevents big audio output fluctuations due to variation
of the modulation depth of the transmitter. The AVL can be switched on and off via the I2C-bus.
For the TDA8373 the AVL is active over an input voltage range (measured at the de-emphasis output) between
75 and 750 mV (RMS). For the TDA8374 this input level is dependent on the crystals which are connected to the
colour decoder. When only 3.5 MHz crystals are connected (indicated via the XA/XB bits) the active input level is
identical to that of the TDA8373. When a 4.4 MHz crystal is connected the input signal range is increased to
150 to 1500 mV (RMS), this to cope with the larger FM swing of European transmitters.
The AVL control curve for the 2 standards is given in Fig.29 and Fig.30. The control range of +6 to
14 dB is valid
for input signals with 50% of the maximum frequency deviation.
17. Vi = 100 mV (RMS), f = 5.5 MHz; FM: 1 kHz, ±17.5 kHz deviation, 15 kHz bandwidth; audio attenuator at 6 dB.
18. Vi = 100 mV (RMS), f = 4.5 to 5.5 MHz, FM: 1 kHz, ±100 kHz deviation.
19. Unweighted RMS value, Vi = 100 mV (RMS), FM: 1 kHz, ±50 kHz deviation, volume control: 6 dB.
20. Audio attenuator at
20 dB; temperature range = 10 to 50 °C.
21. Signal with negative-going sync. Amplitude includes sync pulse amplitude.
22. This parameter is measured at nominal settings of the various controls.
23. Indicated as a signal for a colour bar with 75% saturation (chroma-to-burst ratio = 2.2 : 1).
24. Nominal contrast is specified with the DAC in position 20H. Nominal saturation as maximum
10 dB. At nominal
settings of brightness and white point the black level at the outputs is 300 mV lower than the level of the black current
measuring pulses.
25. The luminance output and input of the TDA8375A, TDA8377A, TDA8375 and TDA8377 can be connected directly.
When additional picture improvement ICs (such as the TDA9170) are applied the inputs of these ICs must be
AC-coupled because of the black level clamp requirement. The output of the picture improvement ICs can be directly
coupled to the luminance input as long as the DC level of the signal has a value between 1 and 7 V.
To be able to apply CTI ICs such as the TDA4565 and TDA4566 the gain of the luminance channel can be increased
via the setting of the GAI bit in the I2C-bus subaddress 03.
S/N = 20 log
V
O(b-w)
V
m rms
() B =5MHz
()
---------------------------------------------------------
相关PDF资料 |
PDF描述 |
|---|---|
| TDA8374C/N3 | SPECIALTY CONSUMER CIRCUIT, PDIP56 |
| TDA8375A/N1 | SPECIALTY CONSUMER CIRCUIT, PDIP56 |
| TDA8375AH/N3 | SPECIALTY CONSUMER CIRCUIT, PQFP64 |
| TDA8377/N3 | SPECIALTY CONSUMER CIRCUIT, PDIP56 |
| TDA6403AM/C2 | VIDEO TUNER, PDSO28 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TDA8374B | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:I2C-bus controlled economy PAL/NTSC and NTSC TV-processors |
| TDA8374BH | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:I2C-bus controlled economy PAL/NTSC and NTSC TV-processors |
| TDA8375 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:I2C-bus controlled economy PAL/NTSC and NTSC TV-processors |
| TDA8375A | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:I2C-bus controlled economy PAL/NTSC and NTSC TV-processors |
| TDA8375AH | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:I2C-bus controlled economy PAL/NTSC and NTSC TV-processors |
发布紧急采购，3分钟左右您将得到回复。