- 您现在的位置：买卖IC网 > PDF目录98218 > THS1041CDWRG4 (TEXAS INSTRUMENTS INC) 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28 PDF资料下载
参数资料
| 型号： | THS1041CDWRG4 |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | ADC |
| 英文描述： | 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28 |
| 封装： | GREEN, PLASTIC, SOIC-28 |
| 文件页数： | 26/41页 |
| 文件大小： | 777K |
| 代理商： | THS1041CDWRG4 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页
THS1041
SLAS289C OCTOBER 2001 REVISED OCTOBER 2004
32
www.ti.com
APPLICATION INFORMATION
steady-state clamp voltage error (continued)
V
COS
VDROOP = VAIN
tc
td
V(Clamp)
VAIN
VM
Figure 47. Approximate Waveforms at AIN During Droop and Clamping
The voltage change at AIN during acquisition has been approximated as a linear charging ramp by assuming
that almost all of VCOS appears across RIN, giving a charging current VCOS/RIN (this is a reasonable
approximation when VCOS is large enough to be of concern). The voltage change at AIN during clamp
acquisition is then:
DV
AIN +
V
COS
t
d
R
IN
C
IN
The peak-to-peak voltage variation at AIN must equal the clamp droop voltage at steady state. Equating the
droop voltage to the clamp acquisition voltage change gives:
V
COS +
R
IN
I
IN
t
d
tc
Thus for low offset voltage, keep RIN low, design for low droop and ensure that the ratio td/tc is not unreasonably
large.
reference decoupling
VREF pin
When the on-chip reference generator is enabled, the VREF pin should be decoupled to the circuit board’s
analog ground plane close to the THS1041 AGND pin via a 1-
F capacitor and a 0.1-F ceramic capacitor.
REFT and REFB pins
In any mode of operation, the REFT and REFB pins should be decoupled as shown in Figure 48. Use short
board traces between the THS1041 and the capacitors to minimize parasitic inductance.
THS1041
REFT
REFB
0.1
F
10
F
0.1
F
0.1
F
Figure 48. Recommended Decoupling for the ADC Reference Pins REFT and REFB
(19)
(20)
相关PDF资料 |
PDF描述 |
|---|---|
| THS1041IDWRG4 | 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28 |
| THS1041CDW | 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28 |
| THS1041CPW | 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28 |
| THS1041IPW | 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28 |
| THS1041CDWR | 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| THS1041CPW | 功能描述:模数转换器 - ADC 10 Bit 40 MSPS Lo-Pwr RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| THS1041CPWG4 | 功能描述:模数转换器 - ADC 10 Bit 40 MSPS Lo-Pwr RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| THS1041CPWR | 功能描述:模数转换器 - ADC 10 Bit 40 MSPS Lo-Pwr RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| THS1041CPWRG4 | 功能描述:模数转换器 - ADC 10 Bit 40 MSPS Lo-Pwr RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| THS1041EVM | 功能描述:数据转换 IC 开发工具 THS1041 Eval Mod RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V |
发布紧急采购，3分钟左右您将得到回复。