- 您现在的位置：买卖IC网 > PDF目录98229 > THS7365IPW (TEXAS INSTRUMENTS INC) 6 CHANNEL, VIDEO AMPLIFIER, PDSO20 PDF资料下载
参数资料
| 型号： | THS7365IPW |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 音频／视频放大 |
| 英文描述： | 6 CHANNEL, VIDEO AMPLIFIER, PDSO20 |
| 封装： | PLASTIC, TSSOP-20 |
| 文件页数： | 30/52页 |
| 文件大小： | 1599K |
| 代理商： | THS7365IPW |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页当前第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
INPUT MODE OF OPERATION: AC BIAS
Level
Shift
Internal
Circuitry
+3.3V
800kW
R
PU
Input
Pin
Input
C
0.1 F
m
IN
V
=V
DC
S
800kW
800k
+R
W
PU
(1)
SBOS467 – MARCH 2009.................................................................................................................................................................................................. www.ti.com
However, what happens if the input signal goes
above the 0-V input level? The problem is the video
Sync-tip clamps work very well for signals that have
signal is always above this level and must not be
horizontal and/or vertical syncs associated with them;
altered in any way. Thus, if the sync level of the input
however, some video signals do not have a sync
signal is above this 0-V level, then the internal
embedded within the signal. If ac-coupling of these
discharge (sink) current reduces the ac-coupled bias
signals is desired, then a dc bias is required to
signal to the proper 0-V level.
properly set the dc operating point within the
This discharge current must not be large enough to
THS7365. This function is easily accomplished with
alter the video signal appreciably or picture quality
the THS7365 by simply adding an external pull-up
issues may arise. This effect is often seen by looking
resistor to the positive power supply, as shown in
at the tilt (droop) of a constant luma signal being
applied and the resulting output level. The associated
change in luma level from the beginning and end of
the video line is the amount of line tilt (droop).
If the discharge current is very small, the amount of
tilt is very low, which is a generally a good thing.
However, the amount of time for the system to
capture the sync signal could be too long. This effect
is also termed hum rejection. Hum arises from the ac
line voltage frequency of 50 Hz or 60 Hz. The value
of the discharge current and the ac-coupling capacitor
combine to dictate the hum rejection and the amount
of line tilt.
To allow for both dc- and ac-coupling in the same
Figure 119. AC-Bias Input Mode Circuit
part, the THS7365 incorporates an 800-k
resistor to
Configuration
ground. Although a true constant current sink is
preferred over a resistor, there can be issues when
the voltage is near ground. This configuration can
The dc voltage appearing at the input pin is equal to
cause the current sink transistor to saturate and
cause potential problems with the signal. The 800-k
resistor is large enough to not impact a dc-coupled
DAC termination. For discharging an ac-coupled
source, Ohm’s Law is used. If the video signal is 1 V,
The THS7365 allowable input range is approximately
then there is 1 V/800 k
= 1.25-
A of discharge
0 V to (VS+ – 1.5 V), allowing for a very wide input
current. If more hum rejection is desired or there is a
voltage range. As such, the input dc bias point is very
loss of sync occurring, then simply decrease the
flexible, with the output dc bias point being the
0.1-
F input coupling capacitor. A decrease from
primary factor. For example, if the output dc bias
0.1
F to 0.047 F increases the hum rejection by a
point is desired to be 1.6 V on a 3.3-V supply, then
factor of 2.1. Alternatively, an external pull-down
the input dc bias point should be (1.6 V – 300 mV)/2
resistor to ground may be added that decreases the
= 0.65 V. Thus, the pull-up resistor calculates to
overall
resistance
and
ultimately
increases
the
approximately 3.3 M
, resulting in 0.644 V. If the
discharge current.
output dc-bias point is desired to be 1.6 V with a 5-V
To ensure proper stability of the ac STC control loop,
power supply, then the pull-up resistor calculates to
the source impedance must be less than 1-k
with
approximately 5.36 M
.
the input capacitor in place. Otherwise, there is a
Keep in mind that the internal 800-k
resistor has
possibility of the control loop ringing, which may
approximately
a
±20%
variance.
As
such,
the
appear on the output of the THS7365. Because most
calculations should take this variance into account.
DACs or encoders use resistors to establish the
For the 0.644-V example above, using an ideal
voltage, which are typically less than 300-
, meeting
3.3-M
resistor,
the
input
dc
bias
voltage
is
the less than 1-k
requirement is easily done.
approximately 0.644 V ± 0.1 V.
However, if the source impedance looking from the
THS7365 input perspective is very high, then simply
The value of the output bias voltage is very flexible
adding a 1-k
resistor to GND ensures proper
and is left to each individual design. It is important to
operation of the THS7365.
ensure that the signal does not clip or saturate the
video signal. Thus, it is recommended to ensure the
output bias voltage is between 0.9 V and (VS+ – 1 V).
For 100% color saturated CVBS or signals with
36
Copyright 2009, Texas Instruments Incorporated
Product Folder Link(s): THS7365
相关PDF资料 |
PDF描述 |
|---|---|
| THS7368IPWR | 6 CHANNEL, VIDEO AMPLIFIER, PDSO20 |
| THS7368IPW | 6 CHANNEL, VIDEO AMPLIFIER, PDSO20 |
| THS7372IPWR | 4 CHANNEL, VIDEO AMPLIFIER, PDSO14 |
| THS7372IPW | 4 CHANNEL, VIDEO AMPLIFIER, PDSO14 |
| THS7374IPWR | 4 CHANNEL, VIDEO AMPLIFIER, PDSO14 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| THS7365IPWR | 功能描述:视频放大器 6Ch Video Amp RoHS:否 制造商:ON Semiconductor 通道数量:4 电源类型: 工作电源电压:3.3 V, 5 V 电源电流: 最小工作温度: 最大工作温度: 封装 / 箱体:TSSOP-14 封装:Reel |
| THS7368 | 制造商:TI 制造商全称:Texas Instruments 功能描述:6-Channel Video Amplifier with 3-SD and 3-SD/ED/HD/Full-HD Filters and 6-dB Gain |
| THS7368EVM | 功能描述:放大器 IC 开发工具 THS7368EVM Eval Mod RoHS:否 制造商:International Rectifier 产品:Demonstration Boards 类型:Power Amplifiers 工具用于评估:IR4302 工作电源电压:13 V to 23 V |
| THS7368IPW | 功能描述:视频放大器 6-Ch Video Amp RoHS:否 制造商:ON Semiconductor 通道数量:4 电源类型: 工作电源电压:3.3 V, 5 V 电源电流: 最小工作温度: 最大工作温度: 封装 / 箱体:TSSOP-14 封装:Reel |
| THS7368IPW | 制造商:Texas Instruments 功能描述:Video Amplifier IC 制造商:Texas Instruments 功能描述:IC, VIDEO AMPLIFIER, HEX, 350MHZ TSSOP20 |
发布紧急采购，3分钟左右您将得到回复。