- 您现在的位置：买卖IC网 > PDF目录98252 > TLV2556IPWR (TEXAS INSTRUMENTS INC) 11-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO20 PDF资料下载
参数资料
| 型号： | TLV2556IPWR |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | ADC |
| 英文描述： | 11-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO20 |
| 封装： | GREEN, PLASTIC, TSSOP-20 |
| 文件页数： | 23/37页 |
| 文件大小： | 729K |
| 代理商： | TLV2556IPWR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页
TLV2556
SLAS355A – DECEMBER 2001 – REVISED SEPTEMBER 2002
3
www.ti.com
Terminal Functions
TERMINAL
I/O
DESCRIPTION
NAME
NO.
I/O
DESCRIPTION
AIN0 – AIN10
1 – 9,
11, 12
I
Analog input. These 11 analog-signal inputs are internally multiplexed.
CS
15
I
Chip select. A high-to-low transition on CS resets the internal counters and controls and enables DATA OUT,
DATA IN, and I/O CLOCK. A low-to-high transition disables DATA IN and I/O CLOCK within a setup time.
DATA IN
17
I
Serial data input. The 4-bit serial data can be used as address selects the desired analog input channel or
test voltage to be converted next, or a command to activate other other features. The input data is presented
with the MSB (D7) first and is shifted in on the first four rising edges of the I/O CLOCK. After the four
address/command bits are read into the command register CMR, I/O CLOCK clocks the remaining four bits
of configuration in.
DATA OUT
16
O
The 3-state serial output for the A/D conversion result. DATA OUT is in the high-impedance state when CS
is high and active when CS is low. With a valid CS, DATA OUT is removed from the high-impedance state
and is driven to the logic level corresponding to the MSB(most significant bit)/LSB(least significant bit) value
of the previous conversion result. The next falling edge of I/O CLOCK drives DATA OUT to the logic level
corresponding to the next MSB/LSB, and the remaining bits are shifted out in order.
INT/EOC
19
O
Status output, used to indicate the end of conversion (EOC) or an interrupt (INT) to host processor.
Programmed as INT (interrupt): INT goes from a high to a low logic level after the conversion is complete and
the data is ready for transfer. INT is cleared by a rising I/O CLOCK transition.
Programmed as EOC: EOC goes from a high to a low logic level after the falling edge of the last I/O CLOCK
and remains low until the conversion is complete and the data is ready for transfer.
GND
10
Ground. GND is the ground return terminal for the internal circuitry. Unless otherwise noted, all voltage
measurements are with respect to GND.
I/O CLOCK
18
I
Input /output clock. I/O CLOCK receives the serial input and performs the following four functions:
1. It clocks the eight input data bits into the input data register on the first eight rising edges of I/O CLOCK
with the multiplexer address available after the fourth rising edge.
2. On the fourth falling edge of I/O CLOCK, the analog input voltage on the selected multiplexer input
begins charging the capacitor array and continues to do so until the last falling edge of I/O CLOCK.
3. The remaining 11 bits of the previous conversion data are shifted out on DATA OUT. Data changes on the
falling edge of I/O CLOCK.
4. Control of the conversion is transferred to the internal state controller on the falling edge of the last
I/O CLOCK.
REF +
14
I/O
Positive reference voltage The upper reference voltage value (nominally VCC) is applied to REF+. The
maximum analog input voltage range is determined by the difference between the voltage applied to terminals
REF+ and REF–.
When the internal reference is used it is capable of driving a 10-k
, 10-pF load.
REF –
13
I/O
Negative reference voltage. The lower reference voltage value (nominally ground) is applied to REF–. This
pin is connected to analog ground (GND of the ADC) when the internal reference is used.
VCC
20
Positive supply voltage
相关PDF资料 |
PDF描述 |
|---|---|
| TLV2556IDW | 11-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO20 |
| TLV2556IPWG4 | 11-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO20 |
| TLV2556MPWREP | 11-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO20 |
| TLV2556MPWREPG4 | 11-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO20 |
| TLV320ADC3001IYZHT | 2-CH 16-BIT PROPRIETARY METHOD ADC, SERIAL ACCESS, PBGA16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TLV2556IPWRG4 | 功能描述:模数转换器 - ADC 12-Bit 200 KSPS 11 Ch Lo-Pwr RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| TLV2556MPWREP | 功能描述:模数转换器 - ADC EP 12B,200KSPS,11Ch Low Pwr,Serial ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| TLV2556MPWREPG4 | 功能描述:模数转换器 - ADC EP 12B,200KSPS,11Ch RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| TLV2620ID | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| TLV2620IDBVR | 功能描述:运算放大器 - 运放 800 uA/ch 11MHz RRO Lo-Vltg 1-Ch RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。