- 您现在的位置：买卖IC网 > PDF目录199412 > TMP86CH09NG 8-BIT, MROM, 16 MHz, MICROCONTROLLER, PDIP32 PDF资料下载
参数资料
| 型号： | TMP86CH09NG |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, MROM, 16 MHz, MICROCONTROLLER, PDIP32 |
| 封装： | 0.400 INCH, 1.78 MM PITCH, LEAD FREE, PLASTIC, SDIP-32 |
| 文件页数： | 4/120页 |
| 文件大小： | 1743K |
| 代理商： | TMP86CH09NG |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页
Page 90
9. 8-Bit TimerCounter (TC3, TC4)
9.1 Configuration
TMP86FH09ANG
Figure 9-2 8-Bit Timer Mode Timing Chart (TC4)
9.3.2 8-Bit Event Counter Mode (TC3, 4)
In the 8-bit event counter mode, the up-counter counts up at the falling edge of the input pulse to the TCj pin.
When a match between the up-counter and the TTREGj value is detected, an INTTCj interrupt is generated and
the up-counter is cleared. After being cleared, the up-counter restarts counting at the falling edge of the input
pulse to the TCj pin. Two machine cycles are required for the low- or high-level pulse input to the TCj pin.
Therefore, a maximum frequency to be supplied is fc/24 Hz in the NORMAL1/2 or IDLE1/2 mode, and fs/24
Hz in the SLOW1/2 or SLEEP1/2 mode.
Note 1: In the event counter mode, fix TCjCR<TFFj> to 0. If not fixed, the PDOj, PWMj and PPGj pins may output
pulses.
Note 2: In the event counter mode, do not change the TTREGj setting while the timer is running. Since TTREGj is
not in the shift register configuration in the event counter mode, the new value programmed in TTREGj is in
effect immediately after the programming. Therefore, if TTREGi is changed while the timer is running, an
expected operation may not be obtained.
Note 3: j = 3, 4
Figure 9-3 8-Bit Event Counter Mode Timing Chart (TC4)
9.3.3 8-Bit Programmable Divider Output (PDO) Mode (TC3, 4)
This mode is used to generate a pulse with a 50% duty cycle from the PDOj pin.
In the PDO mode, the up-counter counts up using the internal clock. When a match between the up-counter
and the TTREGj value is detected, the logic level output from the PDOj pin is switched to the opposite state and
the up-counter is cleared. The INTTCj interrupt request is generated at the time. The logic state opposite to the
timer F/Fj logic level is output from the PDOj pin. An arbitrary value can be set to the timer F/Fj by
TCjCR<TFFj>. Upon reset, the timer F/Fj value is initialized to 0.
To use the programmable divider output, set the output latch of the I/O port to 1.
1
2
3
n-1
n 0
1
n-1
n
2
0
1
2
0
n
?
Internal
Source Clock
Counter
Match detect
Counter clear
Match detect
Counter clear
TC4CR<TC4S>
TTREG4
INTTC4 interrupt request
1
0
2
n-1
n 0
1
2
0
n
?
Counter
Match detect
Counter
clear
n-1
n
2
0
1
Match detect
Counter
clear
TC4CR<TC4S>
TTREG4
INTTC4 interrupt request
TC4 pin input
相关PDF资料 |
PDF描述 |
|---|---|
| TMP86CM29BU | 8-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP64 |
| TMP86FH09NG | 8-BIT, FLASH, 16 MHz, MICROCONTROLLER, PDIP32 |
| TMP86FS49BUG | 8-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP64 |
| TMP86PS25F | 8-BIT, OTPROM, 16 MHz, MICROCONTROLLER, PQFP100 |
| TMP87C800N | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP64 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TMP86CH12MG | 制造商:TOSHIBA 制造商全称:Toshiba Semiconductor 功能描述:8 Bit Microcontroller |
| TMP86CH21AUG | 制造商:TOSHIBA 制造商全称:Toshiba Semiconductor 功能描述:8 Bit Microcontroller |
| TMP86CH21F | 制造商:TOSHIBA 制造商全称:Toshiba Semiconductor 功能描述:CMOS 8-Bit Microcontroller |
| TMP86CH21U | 制造商:TOSHIBA 制造商全称:Toshiba Semiconductor 功能描述:CMOS 8-Bit Microcontroller |
| TMP86CH22UG | 制造商:TOSHIBA 制造商全称:Toshiba Semiconductor 功能描述:8 Bit Microcontroller |
发布紧急采购，3分钟左右您将得到回复。