参数资料
型号: TPS5210PWPG4
厂商: TEXAS INSTRUMENTS INC
元件分类: 稳压器
英文描述: 2 A SWITCHING CONTROLLER, 200 kHz SWITCHING FREQ-MAX, PDSO28
封装: GREEN, PLASTIC, HTSSOP-28
文件页数: 14/35页
文件大小: 846K
代理商: TPS5210PWPG4
TPS5210
PROGRAMMABLE SYNCHRONOUS BUCK REGULATOR CONTROLLER
SLVS171A SEPTEMBER 1998 REVISED MAY 1999
21
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
frequency calculation
A detailed derivation of frequency calculation is shown in the application report, “Designing Fast Response
Synchronous Buck Regulators Using the TPS5210”, TI Literature number SLVA044. When less accurate results
are acceptable, the simplified equation shown below can be used:
fs
V
O
V
I * VO
ESR
V
I
L
Hysteresis Window
Control Section
Below are the equations needed to select the various components within the control section. Details and the
derivations of the equations used in this section are available in the application report “Designing Fast Response
Synchronous Buck Regulators Using the TPS5210”, TI Literature number SLVA044.
output voltage selection
Of course the most important function of the power supply is to regulate the output voltage to a specific value.
Values between 1.3 V and 3.5 V can be easily set by shorting the correct VID inputs to ground. Values above
the maximum reference voltage (3.5 V) can be set by setting the reference voltage to any convenient voltage
within its range and selecting values for R2 and R3 to give the correct output. Select R3:
R3 << than VREF/IBIAS(VSENSE); a recommended value is 10 k
Then, calculate R2 using:
V
O +
V
REF 1 )
R2
R3
R2
+
R3
V
O *
V
REF
V
REF
or
R2 and R3 can also be used to make small adjusts to the output voltage within the reference-voltage range
and/or to adjust for load-current active droop compensation. If there is no need to adjust the output voltage, R3
can be eliminated. R2, R3 (if used), and C7 are used as a noise filter; calculate using:
C7
+
150 ns
R2
R3
slowstart timing
Slowstart reduces the startup stresses on the power-stage components and reduces the input current surge.
Slowstart timing is a function of the reference-voltage current (determined by R6) and is independent of the
reference voltage. The first step in setting slowstart timing will be to determine R6:
R6 should be between 7 k
and 300 k, a recommended value is 20 k.
Set the slowstart timing using the formula:
C5
+
t
SS
5
R
VREFB
t
SS
(5
R6)
Where C5 = Slowstart capacitance in
F
tSS = Slowstart timing in s
RVREFB = Resistance from VREFB to GND in ohms (≈ R6)
相关PDF资料
PDF描述
TPS5210PWPR 2 A SWITCHING CONTROLLER, 200 kHz SWITCHING FREQ-MAX, PDSO28
TPS5210PWP 2 A SWITCHING CONTROLLER, 200 kHz SWITCHING FREQ-MAX, PDSO28
TPS5300DAPR 3.3 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO32
TPS5300DAP 3.3 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO32
TPS5300DAPRG4 3.3 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO32
相关代理商/技术参数
参数描述
TPS5210PWPR 功能描述:DC/DC 开关控制器 Synch Buck Cntrlr Volume Control RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK
TPS5210PWPRG4 功能描述:DC/DC 开关控制器 Synch Buck Cntrlr Volume Control RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK
TPS5211 制造商:TI 制造商全称:Texas Instruments 功能描述:HIGH FREQUENCY PROGRAMMABLE HYSTERETIC REGULATOR CONTROLLER
TPS5211PWP 功能描述:IC REG CTRLR BUCK PWM 28-HTSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR)
TPS5211PWPR 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC