- 您现在的位置：买卖IC网 > PDF目录68419 > TPS5210PWPG4 (TEXAS INSTRUMENTS INC) 2 A SWITCHING CONTROLLER, 200 kHz SWITCHING FREQ-MAX, PDSO28 PDF资料下载
参数资料
| 型号： | TPS5210PWPG4 |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 稳压器 |
| 英文描述： | 2 A SWITCHING CONTROLLER, 200 kHz SWITCHING FREQ-MAX, PDSO28 |
| 封装： | GREEN, PLASTIC, HTSSOP-28 |
| 文件页数： | 30/35页 |
| 文件大小： | 846K |
| 代理商： | TPS5210PWPG4 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页当前第30页第31页第32页第33页第34页第35页
TPS5210
PROGRAMMABLE SYNCHRONOUS BUCK REGULATOR CONTROLLER
SLVS171A SEPTEMBER 1998 REVISED MAY 1999
4
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
detailed description
VREF
The reference/voltage identification (VID) section consists of a temperature-compensated bandgap reference
and a 5-bit voltage selection network. The 5 VID terminals are inputs to the VID selection network and are
TTL-compatible inputs internally pulled up to 5 V by a resistor divider connected to VCC. The VID codes conform
to the Intel VRM 8.3 DC-DC Converter Specification for voltage settings between 1.8 V and 3.5 V, and they are
decremented by 50 mV, down to 1.3 V, for the lower VID settings. Voltages higher than VREF can be implemented
using an external divider. Refer to Table 1 for the VID code settings. The output voltage of the VID network, VREF,
is within
±1% of the nominal setting over the VID range of 1.3 V to 2.5 V, including a junction temperature range
of 5
°C to +125°C, and a VCC supply voltage range of 11.4 V to 12.6 V. The output of the reference/VID network
is indirectly brought out through a buffer to the VREFB pin. The voltage on this pin will be within 2% of VREF. It
is not recommended to drive loads with VREFB, other than setting the hysteresis of the hysteretic comparator,
because the current drawn from VREFB sets the charging current for the slowstart capacitor. Refer to the
slowstart section for additional information.
hysteretic comparator
The hysteretic comparator regulates the output voltage of the synchronous-buck converter. The hysteresis is
set by 2 external resistors and is centered on VREF. The 2 external resistors form a resistor divider from VREFB
to ANAGND, with the output voltage connecting to the VHYST pin. The hysteresis of the comparator will be equal
to twice the voltage difference between the VREFB and VHYST pins. The propagation delay from the comparator
inputs to the driver outputs is 250 ns (maximum). The maximum hysteresis setting is 60 mV.
low-side driver
The low-side driver is designed to drive low-Rds(on) n-channel MOSFETs. The current rating of the driver is
2 A, source and sink. The bias to the low-side driver is internally connected to the DRV regulator.
high-side driver
The high-side driver is designed to drive low-Rds(on) n-channel MOSFETs. The current rating of the driver is
2 A, source and sink. The high-side driver can be configured either as a ground-referenced driver or as a floating
bootstrap driver. When configured as a floating driver, the bias voltage to the driver is developed from the DRV
regulator. The internal bootstrap diode, connected between the DRV and BOOT pins, is a Schottky for improved
drive efficiency. The maximum voltage that can be applied between BOOT and DRVGND is 30 V. The driver
can be referenced to ground by connecting BOOTLO to DRVGND, and connecting BOOT to either DRV or VCC.
deadtime control
Deadtime control prevents shoot-through current from flowing through the main power FETs during switching
transitions by actively controlling the turn-on times of the MOSFET drivers. The high-side driver is not allowed
to turn on until the gate-drive voltage to the low-side FETs is below 2 V; the low-side driver is not allowed to turn
on until the voltage at the junction of the high-side and low-side FETs (Vphase) is below 2 V.
current sensing
Current sensing is achieved by sampling and holding the voltage across the high-side power FETs while the
high-side FETs are on. The sampling network consists of an internal 60-
switch and an external ceramic hold
capacitor. Recommended value of the hold capacitor is between 0.033
F and 0.1 F. Internal logic controls
the turn-on and turn-off of the sample/hold switch such that the switch does not turn on until the Vphase voltage
transitions high, and the switch turns off when the input to the high-side driver goes low. The sampling will occur
only when the high-side FETs are conducting current. The voltage on the IOUT pin equals 2 times the sensed
high-side voltage. In applications where a higher accuracy in current sensing is required, a sense resistor can
be placed in series with the high-side FETs, and the voltage across the sense resistor can be sampled by the
current sensing circuit.
相关PDF资料 |
PDF描述 |
|---|---|
| TPS5210PWPR | 2 A SWITCHING CONTROLLER, 200 kHz SWITCHING FREQ-MAX, PDSO28 |
| TPS5210PWP | 2 A SWITCHING CONTROLLER, 200 kHz SWITCHING FREQ-MAX, PDSO28 |
| TPS5300DAPR | 3.3 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO32 |
| TPS5300DAP | 3.3 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO32 |
| TPS5300DAPRG4 | 3.3 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO32 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPS5210PWPR | 功能描述:DC/DC 开关控制器 Synch Buck Cntrlr Volume Control RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| TPS5210PWPRG4 | 功能描述:DC/DC 开关控制器 Synch Buck Cntrlr Volume Control RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| TPS5211 | 制造商:TI 制造商全称:Texas Instruments 功能描述:HIGH FREQUENCY PROGRAMMABLE HYSTERETIC REGULATOR CONTROLLER |
| TPS5211PWP | 功能描述:IC REG CTRLR BUCK PWM 28-HTSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR) |
| TPS5211PWPR | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
发布紧急采购，3分钟左右您将得到回复。