- 您现在的位置：买卖IC网 > PDF目录68419 > TPS5210PWPG4 (TEXAS INSTRUMENTS INC) 2 A SWITCHING CONTROLLER, 200 kHz SWITCHING FREQ-MAX, PDSO28 PDF资料下载
参数资料
| 型号： | TPS5210PWPG4 |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 稳压器 |
| 英文描述： | 2 A SWITCHING CONTROLLER, 200 kHz SWITCHING FREQ-MAX, PDSO28 |
| 封装： | GREEN, PLASTIC, HTSSOP-28 |
| 文件页数： | 19/35页 |
| 文件大小： | 846K |
| 代理商： | TPS5210PWPG4 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页
TPS5210
PROGRAMMABLE SYNCHRONOUS BUCK REGULATOR CONTROLLER
SLVS171A SEPTEMBER 1998 REVISED MAY 1999
26
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
layout guidelines
Good power supply results will only occur when care is given to proper design and layout. Layout will affect noise
pickup and generation and can cause a good design to perform with less than expected results. With a range
of currents from milliamps to tens or even hundreds of amps, good power supply layout is much more difficult
than most general PCB design. The general design should proceed from the switching node to the output, then
back to the driver section, and, finally, place the low-level components. Below are several specific points to
consider before layout of a TPS5210 design begins.
1.
All sensitive analog components should be referenced to ANAGND. These include components connected
to SLOWST, DROOP, IOUT, OCP, VSENSE, VREFB, VHYST, BIAS, and LOHIB.
2.
Analog ground and drive ground should be isolated as much as possible. Ideally, analog ground will connect
to the ground side of the bulk storage capacitors on VO, and drive ground will connect to the main ground
plane close to the source of the low-side FET.
3.
Connections from the drivers to the gate of the power FETs, should be as short and wide as possible to
reduce stray inductance. This becomes more critical if external gate resistors are not being used.
4.
The bypass capacitor for the DRV regulator should be placed close to the TPS5210 and be connected to
DRVGND.
5.
The bypass capacitor for VCC should be placed close to the TPS5210 and be connected to DRVGND.
6.
When configuring the high-side driver as a floating driver, the connection from BOOTLO to the power FETs
should be as short and as wide as possible. The other pins that also connect to the power FETs, LOHIB
and LOSENSE, should have a separate connection to the FETS since BOOTLO will have large peak
currents flowing through it.
7.
When configuring the high-side driver as a floating driver, the bootstrap capacitor (connected from BOOT
to BOOTLO) should be placed close to the TPS5210.
8.
When configuring the high-side driver as a ground-referenced driver, BOOTLO should be connected to
DRVGND.
9.
The bulk storage capacitors across VI should be placed close to the power FETS. High-frequency bypass
capacitors should be placed in parallel with the bulk capacitors and connected close to the drain of the
high-side FET and to the source of the low-side FET.
10. High-frequency bypass capacitors should be placed across the bulk storage capacitors on VO.
11. HISENSE and LOSENSE should be connected very close to the drain and source, respectively, of the
high-side FET. HISENSE and LOSENSE should be routed very close to each other to minimize
differential-mode noise coupling to these traces. Ceramic decoupling capacitors should be placed close to
where HISENSE connects to Vin, to reduce high-frequency noise coupling on HISENSE.
相关PDF资料 |
PDF描述 |
|---|---|
| TPS5210PWPR | 2 A SWITCHING CONTROLLER, 200 kHz SWITCHING FREQ-MAX, PDSO28 |
| TPS5210PWP | 2 A SWITCHING CONTROLLER, 200 kHz SWITCHING FREQ-MAX, PDSO28 |
| TPS5300DAPR | 3.3 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO32 |
| TPS5300DAP | 3.3 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO32 |
| TPS5300DAPRG4 | 3.3 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO32 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPS5210PWPR | 功能描述:DC/DC 开关控制器 Synch Buck Cntrlr Volume Control RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| TPS5210PWPRG4 | 功能描述:DC/DC 开关控制器 Synch Buck Cntrlr Volume Control RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| TPS5211 | 制造商:TI 制造商全称:Texas Instruments 功能描述:HIGH FREQUENCY PROGRAMMABLE HYSTERETIC REGULATOR CONTROLLER |
| TPS5211PWP | 功能描述:IC REG CTRLR BUCK PWM 28-HTSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR) |
| TPS5211PWPR | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
发布紧急采购，3分钟左右您将得到回复。