- 您现在的位置：买卖IC网 > PDF目录98282 > TPS54160DGQR (TEXAS INSTRUMENTS INC) 2.7 A SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, PDSO10 PDF资料下载
参数资料
| 型号： | TPS54160DGQR |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 稳压器 |
| 英文描述： | 2.7 A SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, PDSO10 |
| 封装： | GREEN, PLASTIC, MSOP-10 |
| 文件页数： | 5/50页 |
| 文件大小： | 1375K |
| 代理商： | TPS54160DGQR |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页
4.6
4.8
5
5.2
5.4
5.6
0
0.05
0.10
0.15
0.20
I
-OutputCurrent- A
O
V
-InputV
oltage-V
I
V
=5V
O
Start
Stop
3
3.2
3.4
3.6
3.8
4
0
0.05
0.10
0.15
0.20
I
-OutputCurrent- A
O
V
-InputV
oltage-V
I
V
=3.3V
O
Start
Stop
www.ti.com
SLVS795C – OCTOBER 2008 – REVISED OCTOBER 2010
DETAILED DESCRIPTION (continued)
Low Dropout Operation and Bootstrap Voltage (BOOT)
The TPS54160 has an integrated boot regulator, and requires a small ceramic capacitor between the BOOT and
PH pins to provide the gate drive voltage for the high-side MOSFET. The BOOT capacitor is refreshed when the
high-side MOSFET is off and the low-side diode conducts. The value of this ceramic capacitor should be 0.1mF.
A ceramic capacitor with an X7R or X5R grade dielectric with a voltage rating of 10V or higher is recommended
because of the stable characteristics overtemperature and voltage.
To improve drop out, the TPS54160 is designed to operate at 100% duty cycle as long as the BOOT to PH pin
voltage is greater than 2.1V. When the voltage from BOOT to PH drops below 2.1V, the high-side MOSFET is
turned off using an UVLO circuit which allows the low-side diode to conduct and refresh the charge on the BOOT
capacitor. Since the supply current sourced from the BOOT capacitor is low, the high-side MOSFET can remain
on for more switching cycles than are required to refresh the capacitor, thus the effective duty cycle of the
switching regulator is high.
The effective duty cycle during dropout of the regulator is mainly influenced by the voltage drops across the
power MOSFET, inductor resistance, low-side diode and printed circuit board resistance. During operating
conditions in which the input voltage drops and the regulator is operating in continuous conduction mode, the
high-side MOSFET can remain on for 100% of the duty cycle to maintain output regulation, until the BOOT to PH
voltage falls below 2.1V.
Attention must be taken in maximum duty cycle applications which experience extended time periods with light
loads or no load. When the voltage across the BOOT capacitor falls below the 2.1V UVLO threshold, the
high-side MOSFET is turned off, but there may not be enough inductor current to pull the PH pin down to
recharge the BOOT capacitor. The high-side MOSFET of the regulator stops switching because the voltage
across the BOOT capacitor is less than 2.1V. The output capacitor then decays until the difference in the input
voltage and output voltage is greater than 2.1V, at which point the BOOT UVLO threshold is exceeded, and the
device starts switching again until the desired output voltage is reached. This operating condition persists until
the input voltage and/or the load current increases. It is recommended to adjust the VIN stop voltage greater
than the BOOT UVLO trigger condition at the minimum load of the application using the adjustable VIN UVLO
feature with resistors on the EN pin.
The start and stop voltages for typical 3.3V and 5V output applications are shown in Figure 26 and Figure 27.
The voltages are plotted versus load current. The start voltage is defined as the input voltage needed to regulate
the output within 1%. The stop voltage is defined as the input voltage at which the output drops by 5% or stops
switching.
During high duty cycle conditions, the inductor current ripple increases while the BOOT capacitor is being
recharged resulting in an increase in ripple voltage on the output. This is due to the recharge time of the boot
capacitor being longer than the typical high-side off time when switching occurs every cycle.
Figure 26. 3.3V Start/Stop Voltage
Figure 27. 5.0V Start/Stop Voltage
Copyright 2008–2010, Texas Instruments Incorporated
13
Product Folder Link(s): TPS54160
相关PDF资料 |
PDF描述 |
|---|---|
| TPS5420MDREPG4 | 5.2 A SWITCHING REGULATOR, 600 kHz SWITCHING FREQ-MAX, PDSO8 |
| TPS5420MDREP | 5.2 A SWITCHING REGULATOR, 600 kHz SWITCHING FREQ-MAX, PDSO8 |
| TPS54225PWP | 4.5 A SWITCHING REGULATOR, 700 kHz SWITCHING FREQ-MAX, PDSO14 |
| TPS54225PWPR | 4.5 A SWITCHING REGULATOR, 700 kHz SWITCHING FREQ-MAX, PDSO14 |
| TPS54225TPWPRQ1 | SWITCHING REGULATOR, PDSO14 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPS54160DGQRG4 | 功能描述:直流/直流开关调节器 3.5-60V,1.5A Step Down SWIFT Converter RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| TPS54160DRCR | 制造商:TI 制造商全称:Texas Instruments 功能描述:1.5-A, 60-V, STEP-DOWN SWIFT DC/DC CONVERTER WITH ECO-MODE |
| TPS54160DRCT | 制造商:TI 制造商全称:Texas Instruments 功能描述:1.5-A, 60-V, STEP-DOWN SWIFT DC/DC CONVERTER WITH ECO-MODE |
| TPS54160EVM-230 | 功能描述:电源管理IC开发工具 TPS54160 Eval Mod RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| TPS54160EVM-535 | 功能描述:电源管理IC开发工具 Eval Mod for High Brightness LED Drvr RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
发布紧急采购，3分钟左右您将得到回复。