- 您现在的位置：买卖IC网 > PDF目录98282 > TPS54233DG4 (TEXAS INSTRUMENTS INC) 2 A SWITCHING REGULATOR, 390 kHz SWITCHING FREQ-MAX, PDSO8 PDF资料下载
参数资料
| 型号： | TPS54233DG4 |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 稳压器 |
| 英文描述： | 2 A SWITCHING REGULATOR, 390 kHz SWITCHING FREQ-MAX, PDSO8 |
| 封装： | GREEN, PLASTIC, MS-012AA, SOIC-8 |
| 文件页数： | 5/25页 |
| 文件大小： | 789K |
| 代理商： | TPS54233DG4 |
)
2
/(
1
max
_
min
_
CO
O
F
R
C
=
p
ú
ù
ê
é
+
-
=
E S R
O
S W
L P P
O P P
R
C
F
D
I
V
4
)
5
.
0
(
)
OPPMAX
max
LPP
SW
O
D
0.5
V
ESR
=
I
4
F
C
-
(
)
12
OUT
IN(MAX)
OUT
COUT(RMS)
IN(MAX)
OUT
SW
C
V
×
V
1
I
=
×
V
× L
× F
× N
-
÷
÷
è
SLUS859B
– OCTOBER 2008 – REVISED FEBRUARY 2011
Capacitor Selection
The important design factors for the output capacitor are dc voltage rating, ripple current rating, and equivalent
series resistance (ESR). The dc voltage and ripple current ratings cannot be exceeded. The ESR is important
because along with the inductor current it determines the amount of output ripple voltage. The actual value of the
output capacitor is not critical, but some practical limits do exist. Consider the relationship between the desired
closed loop crossover frequency of the design and LC corner frequency of the output filter. In general, it is
desirable to keep the closed loop crossover frequency at less than 1/5 of the switching frequency. With high
switching frequencies such as the 300 kHz frequency of this design, internal circuit limitations of the TPS54233
limit the practical maximum crossover frequency to about 25 kHz. In general, the closed loop crossover
frequency should be higher than the corner frequency determined by the load impedance and the output
capacitor. This limits the minimum capacitor value for the output filter to:
(11)
Where RO is the output load impedance (VO/IO) and fCO is the desired crossover frequency. For a desired
maximum crossover of 25 kHz the minimum value for the output capacitor is around 3.8
μF. This may not satisfy
the output ripple voltage requirement. The output ripple voltage consists of two components; the voltage change
due to the charge and discharge of the output filter capacitance and the voltage change due to the ripple current
times the ESR of the output filter capacitor. The output ripple voltage can be estimated by:
(12)
Where NC is the number of output capacitors in parallel.
The maximum ESR of the output capacitor is determined by the amount of allowable output ripple as specified in
the initial design parameters; so the maximum specified ESR as listed in the capacitor data sheet is given by
(13)
Where
ΔVp-p is the desired peak-to-peak output ripple.
To meet the 100 mV p-p ripple requirement, a single 470
μF aluminum electrolytic output capacitor is chosen for
C9. This is a Panasonic, EEVFK1A471P rated at 10 V with a maximum ESR of 160 m
and a ripple current
rating of 600 mA.
The maximum RMS output ripple current can be calculated using Equation 14
(14)
The calculated total RMS ripple current is 216 mA and the maximum total ESR required is 43 m
. These output
capacitors exceed the requirements by a wide margin and will result in a reliable, high-performance design. The
selected output capacitor must be rated for a voltage greater than the desired output voltage plus = the ripple
voltage. Any derating amount must also be included.
Other capacitor types work well with the TPS54233, depending on the needs of the application.
COMPENSATION COMPONENTS
The external compensation used with the TPS54233 allows for a wide range of output filter configurations. A
large range of capacitor values and types of dielectric are supported. The design example uses ceramic X5R
dielectric output capacitors, but other types are supported.
A Type II compensation scheme is recommended for the TPS54233. The compensation components are chosen
to set the desired closed loop cross over frequency and phase margin for output filter components. The type II
compensation has the following characteristics; a dc gain component, a low frequency pole, and a mid frequency
zero / pole pair.
2008–2011, Texas Instruments Incorporated
13
Product Folder Link(s): TPS54233
相关PDF资料 |
PDF描述 |
|---|---|
| TPS54240QDGQRQ1 | 2.5 A SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, PDSO10 |
| TPS54260DGQR | SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, PDSO10 |
| TPS54260QDGQRQ1 | 2.5 A SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, PDSO10 |
| TPS5430MDDAREPG4 | 8.5 A SWITCHING REGULATOR, 600 kHz SWITCHING FREQ-MAX, PDSO8 |
| TPS54310MPWPREP | 6 A SWITCHING REGULATOR, 775 kHz SWITCHING FREQ-MAX, PDSO20 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPS54233DR | 功能描述:直流/直流开关转换器 28V,2A,300khZ Non- synch Buck RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| TPS54233DRG4 | 功能描述:直流/直流开关转换器 28V,2A,300khZ Non- Synch Buck RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| TPS54233EVM-373 | 功能描述:电源管理IC开发工具 TPS54233EVM-373 Eval Mod RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| TPS54233-Q1 | 制造商:TI 制造商全称:Texas Instruments 功能描述:2-A, 28-V INPUT, STEP-DOWN DC/DC CONVERTER WITH ECO-MODEa?￠ |
| TPS54233QDRQ1 | 功能描述:开关变换器、稳压器与控制器 AC 3.5-28Vin,2A 300kHz SD Converter RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。