- 您现在的位置：买卖IC网 > PDF目录15014 > TPS62410DRCR (Texas Instruments)IC REG BUCK SYNC ADJ 0.8A 10SON PDF资料下载
参数资料
| 型号： | TPS62410DRCR |
| 厂商： | Texas Instruments |
| 文件页数： | 16/33页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 0.8A 10SON |
| 标准包装： | 1 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 2 |
| 输出电压： | 0.6 V ~ 6 V |
| 输入电压： | 2.5 V ~ 6 V |
| PWM 型： | 电压模式 |
| 频率 - 开关： | 2.25MHz |
| 电流 - 输出： | 800mA |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-VFDFN 裸露焊盘 |
| 包装： | 标准包装 |
| 供应商设备封装： | 10-SON 裸露焊盘（3x3） |
| 产品目录页面： | 1033 (CN2011-ZH PDF) |
| 其它名称： | 296-25488-6 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
www.ti.com
SLVS737 – FEBRUARY 2007
DETAILED DESCRIPTION (continued)
100% Duty Cycle Low Dropout Operation
The converters offer a low input to output voltage difference while still maintaining operation with the use of the
100% duty cycle mode. In this mode the P-channel switch is constantly turned on. This is particularly useful in
battery-powered applications to achieve longest operation time by taking full advantage of the whole battery
voltage range; i.e., the minimum input voltage to maintain regulation depends on the load current and output
voltage, and can be calculated as:
Vin min + Vout max ) Iout max
RDSon max ) R L
(3)
With:
Iout max = maximum output current plus inductor ripple current
RDSon max = maximum P-channel switch RDSon
R L = DC resistance of the inductor
Vout max = nominal output voltage plus maximum output voltage tolerance
With decreasing load current, the device automatically switches into pulse skipping operation in which the power
stage operates intermittently based on load demand. By running cycles periodically the switching losses are
minimized and the device runs with a minimum quiescent current maintaining high efficiency.
Under-Voltage Lockout
The under voltage lockout circuit prevents the device from malfunctioning at low input voltages and from
excessive discharge of the battery and disables the converters. The under-voltage lockout threshold is typically
1.5V, max 2.35V. In case the default register values are overwritten by the Interface, the new values in the
registers REG_DEF_1_Low and REG_DEF_2 remain valid as long the supply voltage does not fall under the
under-voltage lockout threshold, independent of whether the converters are disabled.
MODE SELECTION
The MODE/DATA pin allows mode selection between forced PWM Mode and Power Save Mode for both
converters. Furthermore, this pin is a multipurpose pin and provides (besides Mode selection) a one-pin
interface to receive serial data from a host to set the output voltage. This is described in the section EasyScale
Interface.
Connecting this pin to GND enables the automatic PWM and power save mode operation. The converters
operate in fixed-frequency PWM mode at moderate to heavy loads and in the PFM mode during light loads,
maintaining high efficiency over a wide load current range.
Pulling the MODE/DATA pin high forces both converters to operate constantly in the PWM mode even at light
load currents. The advantage is the converters operate with a fixed frequency that allows simple filtering of the
switching frequency for noise sensitive applications. In this mode, the efficiency is lower compared to the power
save mode during light loads. For additional flexibility it is possible to switch from Power Save Mode to forced
PWM mode during operation. This allows efficient power management by adjusting the operation of the
converter to the specific system requirements.
In case the operation mode will be changed from forced PWM mode (MODE/DATA = high) to Power Save Mode
Enable (MODE/DATA = 0) the Power Save Mode will be enabled after a delay time of typically t timeout , which is a
maximum of 520 μ s.
The forced PWM Mode operation is enabled immediately with Pin MODE/DATA set to 1.
ENABLE
The device has for each converter a separate EN pin to start up each converter independently. If EN1, EN2 are
set to high, the corresponding converter starts up with soft start as previously described.
Pulling EN1 and EN2 pin low forces the device into shutdown, with a shutdown quiescent current of typically
1.2 μ A. In this mode, the P and N-Channel MOSFETs are turned-off and the entire internal control circuitry is
switched-off. For proper operation the EN1 and EN2 pins must be terminated and must not be left floating.
16
相关PDF资料 |
PDF描述 |
|---|---|
| VE-J4F-EY-F2 | CONVERTER MOD DC/DC 72V 50W |
| VE-J4D-EY-F4 | CONVERTER MOD DC/DC 85V 50W |
| VE-J4D-EY-F3 | CONVERTER MOD DC/DC 85V 50W |
| MCP16321T-500E/NG | IC REG BUCK SYNC 5V 1A 16-VQFN |
| VI-B13-EV-F1 | CONVERTER MOD DC/DC 24V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TPS62410DRCRG4 | 功能描述:直流/直流开关调节器 2.25MHZ 2x800mA Dual St-Down Cnvrtr RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| TPS62410DRCT | 功能描述:直流/直流开关调节器 2.25MHZ 2x800mA Dual Step-Down RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| TPS62410DRCT | 制造商:Texas Instruments 功能描述:IC DUAL STPDN CONV 2X0.8A 10SON 制造商:Texas Instruments 功能描述:IC, DUAL STPDN CONV 2X0.8A 10SON 制造商:Texas Instruments 功能描述:IC, DUAL STPDN CONV 2X0.8A 10SON; Primary Input Voltage:6V; No. of Outputs:2; Output Voltage:6V; Output Current:800mA; Voltage Regulator Case Style:SON; No. of Pins:10; Operating Temperature Min:-40C; Operating Temperature Max:85C;;RoHS Compliant: Yes |
| TPS62410DRCTG4 | 功能描述:直流/直流开关转换器 2.25MHZ 2x800mA Dual St-Down Cnvrtr RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| TPS62410Q1-EVM | 功能描述:EVALUATION MODULE 制造商:texas instruments 系列:* 零件状态:在售 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。