- 您现在的位置：买卖IC网 > PDF目录136905 > TSC87C52-20IAD (ATMEL CORP) 8-BIT, OTPROM, 20 MHz, MICROCONTROLLER, PDIP40 PDF资料下载
参数资料
| 型号： | TSC87C52-20IAD |
| 厂商： | ATMEL CORP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, OTPROM, 20 MHz, MICROCONTROLLER, PDIP40 |
| 封装： | PLASTIC, DIP-40 |
| 文件页数： | 18/46页 |
| 文件大小： | 4720K |
| 代理商： | TSC87C52-20IAD |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页
24
ATtiny20 [DATASHEET]
8235E–AVR–03/2013
7.1.2
ADC Noise Reduction Mode
When bits SM[2:0] are written to 001, the SLEEP instruction makes the MCU enter ADC Noise Reduction mode, stopping
the CPU but allowing the ADC, the external interrupts, TWI and the watchdog to continue operating (if enabled). This
sleep mode halts clkI/O, clkCPU, and clkNVM, while allowing the other clocks to run.
This mode improves the noise environment for the ADC, enabling higher resolution measurements. If the ADC is
enabled, a conversion starts automatically when this mode is entered.
7.1.3
Power-down Mode
When bits SM[2:0] are written to 010, the SLEEP instruction makes the MCU enter Power-down mode. In this mode, the
oscillator is stopped, while the external interrupts, TWI and the watchdog continue operating (if enabled). Only a
watchdog reset, an external level interrupt on INT0, a pin change interrupt, or a TWI slave interrupt can wake up the
MCU. This sleep mode halts all generated clocks, allowing operation of asynchronous modules only.
7.1.4
Standby Mode
When bits SM[2:0] are written to 100, the SLEEP instruction makes the MCU enter Standby mode. This mode is identical
to Power-down with the exception that the oscillator is kept running. This reduces wake-up time, because the oscillator is
already running and doesn't need to be started up.
7.2
Software BOD Disable
When the Brown-out Detector (BOD) is enabled by BODLEVEL fuses (see Table 19-5 on page 161), the BOD is actively
monitoring the supply voltage during a sleep period. In some devices it is possible to save power by disabling the BOD by
software in Power-Down and Stand-By sleep modes. The sleep mode power consumption will then be at the same level
as when BOD is globally disabled by fuses.
If BOD is disabled by software, the BOD function is turned off immediately after entering the sleep mode. Upon wake-up
from sleep, BOD is automatically enabled again. This ensures safe operation in case the VCC level has dropped during
the sleep period.
When the BOD has been disabled, the wake-up time from sleep mode will be approximately 60μs to ensure that the BOD
is working correctly before the MCU continues executing code.
BOD disable is controlled by the BODS (BOD Sleep) bit of MCU Control Register, see “MCUCR – MCU Control Register”
on page 26. Writing this bit to one turns off BOD in Power-Down and Stand-By, while writing a zero keeps the BOD
active. The default setting is zero, i.e. BOD active.
Writing to the BODS bit is controlled by a timed sequence, see “MCUCR – MCU Control Register” on page 26.
7.3
Power Reduction Register
The Power Reduction Register (PRR), see “PRR – Power Reduction Register” on page 27, provides a method to reduce
power consumption by stopping the clock to individual peripherals. When the clock for a peripheral is stopped then:
The current state of the peripheral is frozen.
The associated registers can not be read or written.
Resources used by the peripheral will remain occupied.
The peripheral should in most cases be disabled before stopping the clock. Clearing the PRR bit wakes up the peripheral
and puts it in the same state as before shutdown.
Peripheral shutdown can be used in Idle mode and Active mode to significantly reduce the overall power consumption.
See “Supply Current of I/O Modules” on page 174 for examples. In all other sleep modes, the clock is already stopped.
相关PDF资料 |
PDF描述 |
|---|---|
| TSC87C52-25AKB | 8-BIT, UVPROM, 25 MHz, MICROCONTROLLER, CQCC44 |
| TSC80C31-20MXR | 8-BIT, 20 MHz, MICROCONTROLLER, UUC40 |
| TSC80C31-25MWB/883 | 8-BIT, 25 MHz, MICROCONTROLLER, UUC40 |
| TSC80C51-12MXR | 8-BIT, MROM, 12 MHz, MICROCONTROLLER, UUC40 |
| TSC80C51-20MWR/883 | 8-BIT, MROM, 20 MHz, MICROCONTROLLER, UUC40 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| TSC888AILT | 功能描述:电流灵敏放大器 Sense Amplifier 20 Gain RoHS:否 制造商:Texas Instruments 通道数量: 共模抑制比（最小值）:110 dB 输入补偿电压:80 uV 电源电压-最大:5.5 V 电源电压-最小:2.7 V 电源电流:350 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-16 封装:Reel |
| TSC888BILT | 功能描述:电流灵敏放大器 Sense Amplifier 50 Gain RoHS:否 制造商:Texas Instruments 通道数量: 共模抑制比（最小值）:110 dB 输入补偿电压:80 uV 电源电压-最大:5.5 V 电源电压-最小:2.7 V 电源电流:350 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-16 封装:Reel |
| TSC888CILT | 功能描述:电流灵敏放大器 Sense Amplifier 100 Gain RoHS:否 制造商:Texas Instruments 通道数量: 共模抑制比（最小值）:110 dB 输入补偿电压:80 uV 电源电压-最大:5.5 V 电源电压-最小:2.7 V 电源电流:350 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-16 封装:Reel |
| TSC9 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:EURO TERMINAL BLOCKS |
| TSC903 | 制造商:Laird Technologies Inc 功能描述:CLIP TO-3P 制造商:Laird Technologies Inc 功能描述:CLIP, TO-3P 制造商:Laird Technologies Inc 功能描述:CLIP, TO-3P; External Width:6.5mm; SVHC:No SVHC (18-Jun-2012); Isolation Voltage:1kV; Length:30mm; Material:Steel; Package / Case:TO-3P, TO-218, TO-247; Packages Cooled:TO-3P, TO-218, TO-247; Pad Thickness Max:0.5mm; Panel Thickness ;RoHS Compliant: Yes 制造商:Laird Technologies Inc 功能描述:CLIP, TO-3P; External Width:6.5mm; SVHC:No SVHC (18-Jun-2012); Isolation Voltage:1kV; Length:30mm; Material:Steel; Package / Case:TO-3P, TO-218, TO-247; Packages Cooled:TO-218, TO-247, TO-3P; Pad Thickness Max:0.5mm; Panel Thickness ;RoHS Compliant: Yes |
发布紧急采购，3分钟左右您将得到回复。