- 您现在的位置：买卖IC网 > PDF目录361776 > W28J800BT90C EEPROM PDF资料下载
参数资料
| 型号： | W28J800BT90C |
| 元件分类： | EEPROM |
| 英文描述： | EEPROM |
| 中文描述： | EEPROM的 |
| 文件页数： | 16/51页 |
| 文件大小： | 1468K |
| 代理商： | W28J800BT90C |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页
W28J800B/T
Read Array Command
Upon initial device power-up and after exit from reset mode, the device defaults to read array mode.
This operation is also initiated by writing the Read Array command. The device remains enabled for
reads until another command is written. Once the internal WSM has started a block erase, full chip
erase, word/byte write or lock-bit configuration the device will not recognize the Read Array command
until the WSM completes its operation unless the WSM is suspended via an Erase Suspend or
Word/Byte Write Suspend command. The Read Array command functions independently of the V
PP
voltage and #RESET can be V
IH
.
Read Identifier Codes Command
The identifier code operation is initiated by writing the Read Identifier Codes command. Following the
command write, read cycles from addresses shown in Figure 4 retrieve the manufacturer, device,
block lock configuration and permanent lock configuration codes (see Table 4 for identifier code
values). To terminate the operation, write another valid command. Like the Read Array command, the
Read Identifier Codes command functions independently of the V
PP
voltage and #RESET can be V
IH
.
Following the Read Identifier Codes command, the following information can be read:
Table 4. Identifier Codes
CODE
ADDRESS(2)
[A18
A0]
DATA(3)
[DQ7
DQ0]
Manufacture Code
00000H
B0H
Top Boot
ECH
Device Code
Bottom Boot
00001H
EDH
DQ0 = 0
DQ0 = 1
Block Lock Configuration
Block is Unlocked
Block is Locked
Reserved for Future Use
BA(1)+2
DQ1
7
DQ0 = 0
DQ0 = 1
Permanent Lock Configuration
Device is Unlocked
Device is Locked ed
Reserved for Future Use
00003H
DQ1
7
Notes:
1. BA selects the specific block lock configuration code to be read. See Figure 4 for the device identifier code memory map.
2. A-1 don’t care in byte mode.
3. DQ15
DQ8 outputs 00H in word mode.
Read Status Register Command
The status register may be read to determine when a block erase, full chip erase, word/byte write or
lock-bit configuration is complete and whether the operation completed successfully. It may be read at
any time by writing the Read Status Register command. After writing this command, all subsequent
read operations output data from the status register until another valid command is written. The status
register contents are latched on the falling edge of #OE or #CE, whichever occurs last. #OE or #CE
must toggle to V
IH
before further reads to update the status register latch. The Read Status Register
command functions independently of the V
PP
voltage. #RESET can be V
IH
.
- 16 -
相关PDF资料 |
PDF描述 |
|---|---|
| W28J800BT90L | EEPROM |
| W28J800TT90C | EEPROM |
| W28J800TT90L | EEPROM |
| W28NK60Z | 30V N-Channel PowerTrench MOSFET |
| W28V400 | FLASH |
相关代理商/技术参数 |
参数描述 |
|---|---|
| W28NK60Z | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:N-CHANNEL 600 V - 0.155з - 27A TO-247 Zener-Protected SuperMESH MOSFET |
| W28-SQ11A-10 | 功能描述:CIRCUIT BREAK 10A W/SWITCH RoHS:否 类别:过电压，电流，温度装置 >> 断路器 系列:W28 标准包装:3 系列:AS168X 断路器类型:热磁动式 电压:65VDC，277/480VAC 电流 - 跳闸(It):30A 极数:3 触动器类型:按片 安装类型:DIN 轨道 其它名称:4420.02104420.0210-ND486-2338AS168X-CB3G300-NDCBE AS168X-CB3G300 |
| W28-SQ11A-15 | 制造商:TE Connectivity 功能描述: |
| W28-SQ11A-3 | 制造商:TE Connectivity 功能描述:Circuit Breaker Thermal 1Pole 3A 250VAC/32VDC |
| W28-SQ11A-5 | 制造商:TE Connectivity 功能描述:Circuit Breaker Thermal 1Pole 5A 250VAC/32VDC |
发布紧急采购，3分钟左右您将得到回复。