- 您现在的位置：买卖IC网 > Datasheet目录368 > W29GL128CL9T (Winbond Electronics)IC FLASH 128MBIT 90NS 56TSOP Datasheet资料下载
参数资料
| 型号： | W29GL128CL9T |
| 厂商： | Winbond Electronics |
| 文件页数： | 23/67页 |
| 文件大小： | 0K |
| 描述： | IC FLASH 128MBIT 90NS 56TSOP |
| 标准包装： | 96 |
| 格式 - 存储器： | 闪存 |
| 存储器类型： | FLASH |
| 存储容量： | 128M（16M x 8，8M x 16） |
| 速度： | 90ns |
| 接口： | 并联 |
| 电源电压： | 2.7 V ~ 3.6 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 56-TFSOP（0.724"，18.40mm 宽） |
| 供应商设备封装： | 56-TSOP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页
W29GL128C
7.3.2
7.3.2.1
Individual (Non-Volatile) Protection Mode
Individual Protection Bits (IPB)
The Individual Protection Bit (IPB) is a nonvolatile bit, one bit per sector, with endurance equal to that
of the Flash memory array. Before erasing, IPB preprogramming and verification is managed by the
device, so no monitoring is necessary.
The Individual Protection Bits are set sector by sector by the IPB program instruction. Once a IPB is
set to “0”, the linked sector is protected, blocking any program and/or erase functions on that sector.
The IPB cannot be erased individually, but executing the “All IPB Erase” instruction will erase all IPB
simultaneously. Read and write functions are disabled when IPB programming is going on for all
sectors until this mode exits.
In case one of the protected sectors need to be unprotected, first, the IPB Lock Bit must be set to “1”
by performing one of the following: power-cycle the device or perform a hardware reset. Second, an
“All IPB Erase instruction needs to be performed. Third, Individual Protection Bits need to be set once
again to reflect the desired settings and finally, the IPB Lock Bit needs to be set once again which
locks the Individual Protection Bits and the device functions normally once again.
Executing an IPB Read instruction to the device is required to verify the programming state of the IPB
for any given sector. Refer to the IPB Program Algorithm flow chart below for details.
Note:
?
?
?
?
7.3.2.2
While IPB Lock Bit is set, Program and/or erase instructions will not be executed and times
out without programming and/or erasing the IPB.
For best protection results, it is recommended to execute the IPB Lock Bit Set instruction early
on in the boot code. Also, protect the boot code by holding #WP/ACC = V IL . Note that the IPB
and DPB bits perform the same when #WP/ACC = V HH , and when #WP/ACC =V IH .
While in the IPB command mode, read within that sector will bring the IPB status back for that
sector. All Read must be executed by the read mode.
Issuing the IPB Instruction Set Exit will reset the device to normal read mode enabling reads
and writes for the array.
Dynamic Protection Bits (DPB)
Dynamic Protection allows the software applications to easily protect sectors against unintentional
changes, although, the protection can be readily disabled when changes are needed.
All Dynamic Protection Bits (DPB) are individually linked to their associated sectors and these volatile
bits can be modified individually (set or cleared). The DPB provide protection schemes for only
unprotected sectors that have their associated IPB cleared. To change a DPB, the “DPB Instruction
Set Entry” must be executed first and then either the DPB Set (programmed to “0”) or DPB Clear
(erased to “1”) commands have to be executed.
This places each sector in the protected or
unprotected state separately. To exit the DPB mode, execute the “DPB Instruction Set Exit” instruction.
Note:
?
When the parts are first shipped, the IPB are cleared (erased to “1”) and upon power up or
reset, the DPB can be set or cleared.
Publication Release Date: August 2, 2013
17
Revision H
相关PDF资料 |
PDF描述 |
|---|---|
| W631GG6KB-15 | IC DDR3 SDRAM 1GBIT 96WBGA |
| W9412G6IH-5 | IC DDR-400 SDRAM 128MB 66TSSOPII |
| W9412G6JH-5I | IC DDR SDRAM 128MBIT 66TSOPII |
| W9425G6EH-5 | IC DDR-400 SDRAM 256MB 66TSSOPII |
| W9425G6JH-5I | IC DDR SDRAM 256MBIT 66TSOPII |
相关代理商/技术参数 |
参数描述 |
|---|---|
| W29GL128CL9T TR | 制造商:Winbond Electronics Corp 功能描述:IC FLASH 128MBIT 90NS 56TSOP |
| W29NK50ZD | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:N-CHANNEL 500 V - 0.11? - 29A TO-247 Fast Diode SuperMESH? MOSFET |
| W2A-1819 | 制造商:Nexans 功能描述:MULTI CONDUCTORS |
| W2A21A101J4T2A | 功能描述:电容器阵列与网络 100v 100pF 5% Tol. RoHS:否 制造商:AVX 电容:0.1 uF 容差:20 % 电压额定值:6.3 V 元件数量:2 工作温度范围: 外壳长度:0.8 mm 外壳宽度:1.6 mm 外壳高度:0.5 mm 端接类型:SMD/SMT 系列:PG |
| W2A21A101KAT2A | 功能描述:电容器阵列与网络 100v 100pF 20% Tol. RoHS:否 制造商:AVX 电容:0.1 uF 容差:20 % 电压额定值:6.3 V 元件数量:2 工作温度范围: 外壳长度:0.8 mm 外壳宽度:1.6 mm 外壳高度:0.5 mm 端接类型:SMD/SMT 系列:PG |
发布紧急采购，3分钟左右您将得到回复。