参数资料
型号: WBLXT9785HC.D0-865113
厂商: CORTINA SYSTEMS INC
元件分类: 网络接口
英文描述: DATACOM, INTERFACE CIRCUIT, PQFP208
封装: ROHS COMPLIANT, PLASTIC, HQFP -208
文件页数: 27/222页
文件大小: 3158K
代理商: WBLXT9785HC.D0-865113
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页第159页第160页第161页第162页第163页第164页第165页第166页第167页第168页第169页第170页第171页第172页第173页第174页第175页第176页第177页第178页第179页第180页第181页第182页第183页第184页第185页第186页第187页第188页第189页第190页第191页第192页第193页第194页第195页第196页第197页第198页第199页第200页第201页第202页第203页第204页第205页第206页第207页第208页第209页第210页第211页第212页第213页第214页第215页第216页第217页第218页第219页第220页第221页第222页
Page 122
Cortina Systems LXT9785 and LXT9785E Advanced 8-Port 10/100 Mbps PHY Transceivers
LXT9785/LXT9785E
Datasheet
249241, Revision 11.0
16 April 2007
4.4 Operating Requirements
4.4
Operating Requirements
4.4.1
Power Requirements
The LXT9785/LXT9785E requires four power supply inputs: VCCD, VCCA, VCCPECL
and VCCIO. The digital and analog circuits require 2.5 V supplies (VCCD, VCCR, and
VCCT). These inputs may be supplied from a single source although decoupling is
required to each respective ground. The fiber VCCPECL supply can be connected to
either 2.5 V or 3.3 V.
A separate power supply may be used for the MII, JTAG and MDIO (VCCIO) interfaces.
The power supply may be either +2.5 V or +3.3 V. VCCIO should be supplied from the
same power source used to supply the controller on the other side of the interface. Refer
for I/O characteristics.
As a matter of good practice, these supplies should be as clean as possible. Typical
filtering and decoupling are shown in Figure 34 on page 165. The power supplies should
be brought up as close to the same time as possible. However, there are no specific
timing requirements.
4.4.2
Clock/SYNC Requirements
4.4.2.1
Reference Clock
The LXT9785/LXT9785E requires a constant enabled reference clock (REFCLK).
REFCLK’s frequency must be 50 MHz for RMII or 125 MHz for SMII/SS-SMII. The
reference clock is used to generate transmit signals and recover receive signals. A
crystal-based clock is recommended over a derived clock (that is, PLL-based) to minimize
timing requirements.
For applications that use a single 8-port sectionalization, REFCLK0 and REFCLK1 must
always be tied together and to the source. In 2x4 applications, REFCLK0 and REFCLK1
are not tied together.
4.4.2.2
TxCLK Signal (SS-SMII only)
The LXT9785/LXT9785E requires a 125 MHz input transmit clock synchronous with
TxDatan and frequency locked to REFCLK. See Figure 22 on page 137.
4.4.2.3
TxSYNC Signal (SMII/SS-SMII)
The LXT9785/LXT9785E requires a 12.5 MHz input pulse for SMII synchronization. See
4.4.2.4
RxSYNC Signal (SS-SMII only)
The LXT9785/LXT9785E provides a 12.5 MHz output pulse synchronous with the
RxDatan outputs. See Figure 23 on page 137.
相关PDF资料
PDF描述
WBLXT9785HC.D0 DATACOM, INTERFACE CIRCUIT, PQFP208
WBLXT9785HE.C2V DATACOM, INTERFACE CIRCUIT, PQFP208
WBLXT9785HE.D0-865114 DATACOM, INTERFACE CIRCUIT, PQFP208
WBLXT9785HE.D0-865115 DATACOM, INTERFACE CIRCUIT, PQFP208
WBLXT9785HE.D0 DATACOM, INTERFACE CIRCUIT, PQFP208
相关代理商/技术参数
参数描述
WBLXT9785HE.D0-865114 制造商:Cortina Systems Inc 功能描述:PHY 8-CH 10Mbps/100Mbps 208-Pin PQFP
WBM-DATA 制造商:Thomas & Betts 功能描述:
WBM-DISHWASH 制造商:Thomas & Betts 功能描述:
WBM-DISPOSAL 制造商:Thomas & Betts 功能描述:
WBM-DUPLEX 制造商:Thomas & Betts 功能描述: