- 您现在的位置：买卖IC网 > PDF目录18749 > XC09-009WNC (Digi International/Maxstream)MOD RF 900MHZ 9600BPS W/WIRE ANT PDF资料下载
参数资料
| 型号： | XC09-009WNC |
| 厂商： | Digi International/Maxstream |
| 文件页数： | 16/36页 |
| 文件大小： | 826K |
| 描述： | MOD RF 900MHZ 9600BPS W/WIRE ANT |
| 标准包装： | 1 |
| 系列： | 9XCite OEM 模块 |
| 频率： | 900MHz |
| 数据传输率 - 最大： | 9.6kbps |
| 调制或协议： | FHSS，FSK |
| 功率 - 输出： | 6dBm |
| 灵敏度： | -108dBm |
| 电源电压： | 2.85 V ~ 5.5 V |
| 电流 - 接收： | 45mA |
| 电流 - 传输： | 55mA |
| 数据接口： | PCB，通孔 |
| 天线连接器： | 板载，导线天线 |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 模块 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
9XCite"燨EM燫F燤odule?燩roduct燤anual爒2.1燵2007.01.04]
2007燤axStream,營nc.
牋牋?6
3.2. Configuration Software
X-CTU is a MaxStream-provided software program used to interface with and configure Max-
Stream RF Modules. The software application is organized into the following four tabs:
" PC Settings tab - Setup PC serial ports for interfacing with an RF module
" Range Test tab - Test the RF module's range and monitor packets sent and received
" Terminal tab - Set and read RF module parameters using AT Commands
" Modem Configuration tab - Set and read RF module parameters
Figure燘1. XCTU燯ser營nterface?PC燬ettings,燫ange燭est,燭erminal燼nd燤odem燙onfiguration爐abs)
NOTE: PC Setting values are visible at the bottom of the Range Test, Terminal and Modem Configura-
tion tabs. A shortcut for editing PC Setting values is available by clicking on any of the values.
Installation
Double-click the "setup_X-CTU.exe" file and follow prompts of the installation screens. This file is
located in the 'software' folder of the MaxStream CD and also under the 'Downloads' section of the
following web page: www.maxstream.net/support/downloads.php
Setup
Serial Communications Software
A terminal program is built into the X-CTU Software. Other terminal programs such as "HyperTer-
minal" can also be used to configure modules and monitor communications. When issuing AT Com-
mands through a terminal program interface, use the following syntax:
Figure燘2. Syntax爁or爏ending燗T燙ommands
NOTE: To read a parameter value stored in a register, leave the parameter field blank.
The example above issues the DT (Destination Address) command to change destination address
of the module to "0x1F". To save the new value to the modules non-volatile memory, issue WR
(Write) command after modifying parameters.
To use the X-CTU software, a module assembly (An RF module mounted to an interface Board)
must be connected to a serial port of a PC.
NOTE: Failure to enter AT Command Mode is most commonly due to baud rate mismatch. The
interface data rate and parity settings of the serial port ("PC Settings" tab) must match those of
the module (BD (Baud Rate) and NB (Parity) parameters respectively).
相关PDF资料 |
PDF描述 |
|---|---|
| FAR-F5KY-740M00-B4UR-Z | FILTER SAW 740MHZ LTE XVII SMD |
| IF-14-30 | XFRMR 115/230V 15V 940MA PCB |
| IF-14-24 | XFRMR 115/230V 12V 1.2A 14VA PCB |
| RF100PC6 | RF ENGINE F-ANT MAX RANGE |
| IF-14-230 | XFRMR 115/230V 115V 120MA PCB |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XC09-009WNI | 功能描述:射频模块 9XCite 4mW transcei re antenna 9600 bps RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm |
| XC0900A-03P | 制造商:ANAREN 制造商全称:Anaren Microwave 功能描述:Hybrid Coupler 3 dB, 90∑ |
| XC0900A-03S | 功能描述:信号调节 811-1000MHz IL:.12dB VSWR:1.12 -55 to 95C RoHS:否 制造商:EPCOS 产品:Duplexers 频率:782 MHz, 751 MHz 频率范围: 电压额定值: 带宽: 阻抗:50 Ohms 端接类型:SMD/SMT 封装 / 箱体:2.5 mm x 2 mm 工作温度范围:- 30 C to + 85 C 封装:Reel |
| XC0900A-03S-CT | 制造商:Anaren Microwave 功能描述:RF HYBRID COUPLER |
| XC0900A-03SR | 制造商:Anaren Microwave 功能描述:HYBRID COUPLERS |
发布紧急采购，3分钟左右您将得到回复。