- 您现在的位置：买卖IC网 > PDF目录18749 > XC09-009WNC (Digi International/Maxstream)MOD RF 900MHZ 9600BPS W/WIRE ANT PDF资料下载
参数资料
| 型号： | XC09-009WNC |
| 厂商： | Digi International/Maxstream |
| 文件页数： | 18/36页 |
| 文件大小： | 826K |
| 描述： | MOD RF 900MHZ 9600BPS W/WIRE ANT |
| 标准包装： | 1 |
| 系列： | 9XCite OEM 模块 |
| 频率： | 900MHz |
| 数据传输率 - 最大： | 9.6kbps |
| 调制或协议： | FHSS，FSK |
| 功率 - 输出： | 6dBm |
| 灵敏度： | -108dBm |
| 电源电压： | 2.85 V ~ 5.5 V |
| 电流 - 接收： | 45mA |
| 电流 - 传输： | 55mA |
| 数据接口： | PCB，通孔 |
| 天线连接器： | 板载，导线天线 |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 模块 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
9XCite"燨EM燫F燤odule?燩roduct燤anual爒2.1燵2007.01.04]
2007燤axStream,營nc.
牋牋?8
Table?02. NonAT燬ettable燩arameters
(Settable/Readable爑sing爐he燲CTU燬oftware?Modem燙onfiguration 爐ab爋nly)
AT
Designator
Command Name & Description
Parameter Range
Command
Category
# Bytes
Returned
Factory
Default
AT
Guard Time After. Set required DI pin silent time after the
Command Sequence Characters of the AT Command Mode
Sequence (BT+ CC + AT).
0x02 0xFFFF
[x 1 ms]
AT Command
Mode Options
2
0x1F4
(500d)
BD
Interface Data Rate. Set serial data rate (baud rate at which
radio modem interfaces with host).
Serial data rate is different than RF data rate which is fixed
and factory-set. If the serial data rate is set higher than RF
data rate, flow control may need to be observed to prevent DI
buffer overrun.
0 6
(1200 - 57600 bps)
Serial
Interfacing
1
Set to equal
radio modems
fixed RF data
rate.
BI
Number of Bits. (7 or 8) Sets number of data bits per
character (bits between start and stop bits).
0 1
0 = 7 bits
1 = 8 bits
Serial
Interfacing
1
1
BT
Guard Time Before. Set required DI pin silent time before the
Command Sequence Characters of the Command Mode
Sequence (BT+ CC + AT).
0 0xFFFF
[x 1 ms]
AT Command
Mode Options
2
0x1F4
(500d)
CC
Command Sequence Character. Set the ASCII character to be
used between Guard Times of the AT Command Mode
Sequence (BT+ CC + AT). The AT Command Mode Sequence
enters the radio modem to AT Command Mode (from Idle
Mode).
0x20 0x7F
AT Command
Mode Options
1
0x2B
(plus sign (+) in
ASCII)
CT
Time before Exit AT Command Mode. Set time period of
inactivity (no valid commands received) after which radio
modem automatically exits from AT Command Mode.
0x02 0xFFFF
[x 100 ms]
AT Command
Mode Options
2
0xC8
(200d)
FL
Software Flow Control. Enable serial software flow control on
the radio modem. (Hardware flow control (CTS
) is on by
default.)
0 - 1
0 = disable
1 = enabled
Serial
Interfacing
1
0
HT
Time before Wake-up Initializer. Set time period of inactivity
(no serial or RF data is sent or received) before a Wake-up
Initializer is sent. Base station tracks awake-status of remote
radios. HT of base radio should be set shorter than ST of
remote radios.
0 0xFFFF
[x 100 ms]
Sleep
(Low Power)
2
0xFFFF
(no wake-up
Initializer will be
sent)
ID
Modem VID. Read radio modem VID (Vendor Identification
Number). Only radio modems with matching VIDs can
communicate with each other.
0 0x7FFF
(above this range is Read-only)
Networking
2
0x3332
LH
Wake-up Initializer Time. Set time of the Wake-up Initializer
used to wake remote radios that are in cyclic sleep mode.
Time of Wake-up Initializer should be longer than that of the
remote radios cyclic sleep cycle (SM 3 - 8).
0 0xFF
[x 100 ms]
Sleep
(Low Power)
1
1
NB
Parity. Select parity format. Settings 0-4 transfer only 8 bits
out the antenna port and generate the parity bit on the radio
modem receiving side.
0 4
0 = 8-none-1, 7-any-1
1 = 8-even-1
2 = 8-odd-1
3 = 8-mark-1, 8-none-2
4 = 8-space-1
Serial
Interfacing
1
0
PW
Pin Wake-up. Enable pin wake-up from Cyclic Sleep Mode.
0 1
0 = disabled
1 = enabled
Sleep
(Low Power)
1
0
RT
DI2 Configuration. Enable RTS
Mode
0 - 1
0 = Disabled
1 = RTS
flow control
Serial
Interfacing
1
0
SB
Stop Bits. Set number of stop bits.
0 1
0 = 1 stop bit
1 = 2 stop bits
Serial
Interfacing
1
0
SM
Sleep Mode. Specify Sleep Mode settings.
0 8
0 = No sleep
1 = Pin Sleep
2 = Serial Port Sleep
3 to 8 = Cyclic intervals
ranging from 0.5 to16.0 seconds
Sleep
(Low Power)
1
0
ST
Time before Sleep. Set time period of inactivity (no serial or
RF data is sent or received) before activating Sleep Mode.
Use with Cyclic Sleep and Serial Port Sleep [refer to SM
Command]
0x10 0xFFFF
[x 100 ms]
Sleep
(Low Power)
2
0x64
(100d)
相关PDF资料 |
PDF描述 |
|---|---|
| FAR-F5KY-740M00-B4UR-Z | FILTER SAW 740MHZ LTE XVII SMD |
| IF-14-30 | XFRMR 115/230V 15V 940MA PCB |
| IF-14-24 | XFRMR 115/230V 12V 1.2A 14VA PCB |
| RF100PC6 | RF ENGINE F-ANT MAX RANGE |
| IF-14-230 | XFRMR 115/230V 115V 120MA PCB |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XC09-009WNI | 功能描述:射频模块 9XCite 4mW transcei re antenna 9600 bps RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm |
| XC0900A-03P | 制造商:ANAREN 制造商全称:Anaren Microwave 功能描述:Hybrid Coupler 3 dB, 90∑ |
| XC0900A-03S | 功能描述:信号调节 811-1000MHz IL:.12dB VSWR:1.12 -55 to 95C RoHS:否 制造商:EPCOS 产品:Duplexers 频率:782 MHz, 751 MHz 频率范围: 电压额定值: 带宽: 阻抗:50 Ohms 端接类型:SMD/SMT 封装 / 箱体:2.5 mm x 2 mm 工作温度范围:- 30 C to + 85 C 封装:Reel |
| XC0900A-03S-CT | 制造商:Anaren Microwave 功能描述:RF HYBRID COUPLER |
| XC0900A-03SR | 制造商:Anaren Microwave 功能描述:HYBRID COUPLERS |
发布紧急采购，3分钟左右您将得到回复。