- 您现在的位置：买卖IC网 > PDF目录18749 > XC09-009WNC (Digi International/Maxstream)MOD RF 900MHZ 9600BPS W/WIRE ANT PDF资料下载
参数资料
| 型号： | XC09-009WNC |
| 厂商： | Digi International/Maxstream |
| 文件页数： | 19/36页 |
| 文件大小： | 826K |
| 描述： | MOD RF 900MHZ 9600BPS W/WIRE ANT |
| 标准包装： | 1 |
| 系列： | 9XCite OEM 模块 |
| 频率： | 900MHz |
| 数据传输率 - 最大： | 9.6kbps |
| 调制或协议： | FHSS，FSK |
| 功率 - 输出： | 6dBm |
| 灵敏度： | -108dBm |
| 电源电压： | 2.85 V ~ 5.5 V |
| 电流 - 接收： | 45mA |
| 电流 - 传输： | 55mA |
| 数据接口： | PCB，通孔 |
| 天线连接器： | 板载，导线天线 |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 模块 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
9XCite"燨EM燫F燤odule?燩roduct燤anual爒2.1燵2007.01.04]
2007燤axStream,營nc.
牋牋?9
3.4. Automatic DIP Switch Configurations
Each time the RF Modem is powered-on, intelligence on the Max-
Stream Interface Board (located inside the RF Modem) sends AT
Commands that program the modem based on positions of the DIP
Switch. Automatic configurations that take place during the power-on
sequence affect RF Modem parameter values as shown below.
To avoid overwriting previously stored custom configurations (due to the automatic configurations
that take place each time the RF Modem is powered-on), it is necessary to disable a processor
located on the XIB-R interface board. To disable the processor, populate J7 of the XIB-R Interface
Board. (By default, J7 jumper is not populated.)
Table?03. RF燤odem燩owerup燨ptions?J7爅umper燼nd燙onfig燬witch)
AT燙ommands燬ent燼s爎esult爋f燚IP燬witch燬ettings?SW?燚IP燬witch)
Condition
Behavior
If J7 is populated
Processor is disabled and AT Commands are not sent to the RF Modem
If Config Switch is pressed
Processor is disabled and RF Modem enters into AT Command Mode
If J7 is NOT populated and Config
Switch is NOT pressed
Execute logic as shown in Table 6.
Condition
Behavior
Serial Interfacing Options
If SW1 is ON (up)
AT Commands sent: ATCS 0 (RS-232 Operation: CTS
function for CTS
line)
ATCD 2 (DO3 - RX LED = low)
If SW1 is OFF (down)
AT Commands sent: ATCS 3 (RS-485 or RS-422 Operation)
ATCD 2 (DO3 - RX LED = low)
Exit AT Command Mode
Always
AT Commands sent: ATCN (Exit AT Command Mode)
相关PDF资料 |
PDF描述 |
|---|---|
| FAR-F5KY-740M00-B4UR-Z | FILTER SAW 740MHZ LTE XVII SMD |
| IF-14-30 | XFRMR 115/230V 15V 940MA PCB |
| IF-14-24 | XFRMR 115/230V 12V 1.2A 14VA PCB |
| RF100PC6 | RF ENGINE F-ANT MAX RANGE |
| IF-14-230 | XFRMR 115/230V 115V 120MA PCB |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XC09-009WNI | 功能描述:射频模块 9XCite 4mW transcei re antenna 9600 bps RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm |
| XC0900A-03P | 制造商:ANAREN 制造商全称:Anaren Microwave 功能描述:Hybrid Coupler 3 dB, 90∑ |
| XC0900A-03S | 功能描述:信号调节 811-1000MHz IL:.12dB VSWR:1.12 -55 to 95C RoHS:否 制造商:EPCOS 产品:Duplexers 频率:782 MHz, 751 MHz 频率范围: 电压额定值: 带宽: 阻抗:50 Ohms 端接类型:SMD/SMT 封装 / 箱体:2.5 mm x 2 mm 工作温度范围:- 30 C to + 85 C 封装:Reel |
| XC0900A-03S-CT | 制造商:Anaren Microwave 功能描述:RF HYBRID COUPLER |
| XC0900A-03SR | 制造商:Anaren Microwave 功能描述:HYBRID COUPLERS |
发布紧急采购，3分钟左右您将得到回复。