参数资料
型号: XR16C850CJ-F
厂商: Exar Corporation
文件页数: 16/56页
文件大小: 0K
描述: IC UART FIFO 128B 44PLCC
标准包装: 27
特点: *
通道数: 1,UART
FIFO's: 128 字节
规程: RS485
电源电压: 2.97 V ~ 5.5 V
带自动流量控制功能:
带IrDA 编码器/解码器:
带故障启动位检测功能:
带调制解调器控制功能:
带CMOS:
安装类型: 表面贴装
封装/外壳: 44-LCC(J 形引线)
供应商设备封装: 44-PLCC(16.59x16.59)
包装: 管件
xr
XR16C850
REV. 2.3.1
2.97V TO 5.5V UART WITH 128-BYTE FIFO
23
2.21
Sleep Mode with Auto Wake-Up
The 850 supports low voltage system designs, hence, a sleep mode is included to reduce its power
consumption when the chip is not actively used.
All of these conditions must be satisfied for the 850 to enter sleep mode:
no interrupts pending for the 850 (ISR bit-0 = 1)
sleep mode is enabled (IER bit-4 = 1)
modem inputs are not toggling (MSR bits 0-3 = 0)
RX input pin is idling at a logic 1
The 850 stops its crystal oscillator to conserve power in the sleep mode. User can check the XTAL2 pin for no
clock output as an indication that the device has entered the sleep mode.
The 850 resumes normal operation by any of the following:
a receive data start bit transition (logic 1 to 0)
a data byte is loaded to the transmitter, THR or FIFO
a change of logic state on any of the modem or general purpose serial inputs: CTS#, DSR#, CD#, RI#
If the 850 is awakened by any one of the above conditions, it will return to the sleep mode automatically after
all interrupting conditions have been serviced and cleared. If the 850 is awakened by the modem inputs, a read
to the MSR is required to reset the modem inputs. In any case, the sleep mode will not be entered while an
interrupt is pending. The 850 will stay in the sleep mode of operation until it is disabled by setting IER bit-4 to a
logic 0.
If the address lines, data bus lines, IOW#, IOR#, CSA#, CSB#, and modem input lines remain steady when the
850 is in sleep mode, the maximum current will be in the microamp range as specified in the DC Electrical
Characteristics on page 42. If the input lines are floating or are toggling while the 850 is in sleep mode, the
current can be up to 100 times more. If any of those signals are toggling or floating, then an external buffer
would be required to keep the address, data and control lines steady to achieve the low current.
A word of caution: owing to the starting up delay of the crystal oscillator after waking up from sleep mode, the
first few receive characters may be lost. Also, make sure the RX input is idling at logic 1 or “marking” condition
during sleep mode. This may not occur when the external interface transceivers (RS-232, RS-485 or another
type) are also put to sleep mode and cannot maintain the “marking” condition. To avoid this, the system design
engineer can use a 47k ohm pull-up resistor on the RX input.
相关PDF资料
PDF描述
MS3116F16-23P CONN PLUG 23POS STRAIGHT W/PINS
XR16C2852CJTR-F IC UART FIFO 128B 44PLCC
D38999/20FB5SA CONN RCPT 5POS WALL MNT W/SCKT
XR16C2850CJTR-F IC UART FIFO 128B 44PLCC
XR68C192IJ-F IC UART FIFI DUAL 44PLCC
相关代理商/技术参数
参数描述
XR16C850CJTR-F 制造商:Exar Corporation 功能描述:UART 1-CH 128Byte FIFO 3.3V/5V 44-Pin PLCC T/R 制造商:Exar Corporation 功能描述:XR16C850CJTR-F
XR16C850CM 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述:
XR16C850CM-0A-EVB 功能描述:UART 接口集成电路 Supports C850 48 ld TQFP, ISA Interface RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
XR16C850CM-F 功能描述:UART 接口集成电路 UARTW/128BYTE FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
XR16C850CMTR-F 功能描述:UART 接口集成电路 UART w/128 Bytes FIFO & IrDA RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel