- 您现在的位置：买卖IC网 > PDF目录16499 > XR16M564IV-0A-EVB (Exar Corporation)EVAL BOARD FOR XR16M564-A 64LQFP PDF资料下载
参数资料
| 型号： | XR16M564IV-0A-EVB |
| 厂商： | Exar Corporation |
| 文件页数： | 15/55页 |
| 文件大小： | 0K |
| 描述： | EVAL BOARD FOR XR16M564-A 64LQFP |
| 标准包装： | 1 |
| 系列： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页
XR16M564/564D
22
1.62V TO 3.63V QUAD UART WITH 32-BYTE FIFO
REV. 1.0.0
2.17
Sleep Mode with Auto Wake-Up
The M564 supports low voltage system designs, hence, a sleep mode is included to reduce its power
consumption when the chip is not actively used.
All of these conditions must be satisfied for the M564 to enter sleep mode:
■ no interrupts pending for all four channels of the M564 (ISR bit-0 = 1)
■ sleep mode of all channels are enabled (IER bit-4 = 1)
■ modem inputs are not toggling (MSR bits 0-3 = 0)
■ RX input pins are idling HIGH
The M564 stops its crystal oscillator to conserve power in the sleep mode. User can check the XTAL2 pin for
no clock output as an indication that the device has entered the sleep mode.
The M564 resumes normal operation by any of the following:
■ a receive data start bit transition (HIGH to LOW)
■ a data byte is loaded to the transmitter, THR or FIFO
■ a change of logic state on any of the modem or general purpose serial inputs: CTS#, DSR#, CD#, RI#
If the M564 is awakened by any one of the above conditions, it will return to the sleep mode automatically after
all interrupting conditions have been serviced and cleared. If the M564 is awakened by the modem inputs, a
read to the MSR is required to reset the modem inputs. In any case, the sleep mode will not be entered while
an interrupt is pending from any channel. The M564 will stay in the sleep mode of operation until it is disabled
by setting IER bit-4 to a logic 0.
If the address lines, data bus lines, IOW#, IOR#, CSA#, CSB#, CSC#, CSD# and modem input lines remain
steady when the M564 is in sleep mode, the maximum current will be in the microamp range as specified in the
DC Electrical Characteristics on page 40. If the input lines are floating or are toggling while the M564 is in
sleep mode, the current can be up to 100 times more. If any of those signals are toggling or floating, then an
external buffer would be required to keep the address, data and control lines steady to achieve the low current.
A word of caution: owing to the starting up delay of the crystal oscillator after waking up from sleep mode, the
first few receive characters may be lost. Also, make sure the RX A-D pins are idling HIGH or “marking”
condition during sleep mode. This may not occur when the external interface transceivers (RS-232, RS-485 or
another type) are also put to sleep mode and cannot maintain the “marking” condition. To avoid this, the
system design engineer can use a 47k ohm pull-up resistor on each of the RX A-D inputs.
2.18
Internal Loopback
The M564 UART provides an internal loopback capability for system diagnostic purposes. The internal
loopback mode is enabled by setting MCR register bit-4 to logic 1. All regular UART functions operate normally.
Figure 13 shows how the modem port signals are re-configured. Transmit data from the transmit shift register
output is internally routed to the receive shift register input allowing the system to receive the same data that it
was sending. The TX pin is held HIGH or mark condition while RTS# and DTR# are de-asserted, and CTS#,
DSR# CD# and RI# inputs are ignored. Caution: the RX input must be held HIGH during loopback test else
upon exiting the loopback test the UART may detect and report a false “break” signal.
相关PDF资料 |
PDF描述 |
|---|---|
| VI-J2H-EZ-S | CONVERTER MOD DC/DC 52V 25W |
| 2-5504971-8 | CA 62.5/125 LDDZP SCDUP SCDUP |
| EEC08DRAS-S734 | CONN EDGECARD 16POS .100 R/A PCB |
| CB5000-000 | HEAT SHRINK TUBING |
| XR16M654IQ100-0B-EB | EVAL BOARD FOR XR16M654-B 100QFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XR16M564IV-0B-EVB | 功能描述:界面开发工具 Eval Board for XR16M564IV-0B RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| XR16M564IV64 | 制造商:EXAR 制造商全称:EXAR 功能描述:1.62V TO 3.63V QUAD UART WITH 32-BYTE FIFO |
| XR16M564IV64-F | 功能描述:UART 接口集成电路 UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR16M564IV80 | 制造商:EXAR 制造商全称:EXAR 功能描述:1.62V TO 3.63V QUAD UART WITH 32-BYTE FIFO |
| XR16M564IV80-0A-EB | 功能描述:界面开发工具 Eval Board for XR16M564IV80-0A RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
发布紧急采购，3分钟左右您将得到回复。