- 您现在的位置：买卖IC网 > PDF目录16499 > XR16M564IV-0A-EVB (Exar Corporation)EVAL BOARD FOR XR16M564-A 64LQFP PDF资料下载
参数资料
| 型号： | XR16M564IV-0A-EVB |
| 厂商： | Exar Corporation |
| 文件页数： | 22/55页 |
| 文件大小： | 0K |
| 描述： | EVAL BOARD FOR XR16M564-A 64LQFP |
| 标准包装： | 1 |
| 系列： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页
XR16M564/564D
29
REV. 1.0.0
1.62V TO 3.63V QUAD UART WITH 32-BYTE FIFO
]
ISR[0]: Interrupt Status
Logic 0 = An interrupt is pending and the ISR contents may be used as a pointer to the appropriate interrupt
service routine.
Logic 1 = No interrupt pending (default condition).
ISR[3:1]: Interrupt Status
These bits indicate the source for a pending interrupt at interrupt priority levels (See Interrupt Source
Table 11).
ISR[4]: Interrupt Status (requires EFR bit-4 = 1)
This bit is enabled when EFR bit-4 is set to a logic 1. ISR bit-4 indicates that the receiver detected a data match
of the Xoff character(s) or a special character.
ISR[5]: Interrupt Status (requires EFR bit-4 = 1)
ISR bit-5 indicates that CTS# or RTS# has changed state from LOW to HIGH.
ISR[7:6]: FIFO Enable Status
These bits are set to a logic 0 when the FIFOs are disabled. They are set to a logic 1 when the FIFOs are
enabled.
4.5
FIFO Control Register (FCR) - Write-Only
This register is used to enable the FIFOs, clear the FIFOs, set the transmit/receive FIFO trigger levels, and
select the DMA mode. The DMA, and FIFO modes are defined as follows:
FCR[0]: TX and RX FIFO Enable
Logic 0 = Disable the transmit and receive FIFO (default).
Logic 1 = Enable the transmit and receive FIFOs. This bit must be set to logic 1 when other FCR bits are
written or they will not be programmed.
TABLE 11: INTERRUPT SOURCE AND PRIORITY LEVEL
PRIORITY
ISR REGISTER STATUS BITS
SOURCE OF INTERRUPT
LEVEL
BIT-5
BIT-4
BIT-3
BIT-2
BIT-1
BIT-0
1
0
1
0
LSR (Receiver Line Status Register)
2
0
1
0
RXRDY (Receive Data Time-out)
3
0
1
0
RXRDY (Received Data Ready)
4
0
1
0
TXRDY (Transmit Ready)
5
0
MSR (Modem Status Register)
6
0
1
0
RXRDY (Received Xoff or Special character)
7
1
0
CTS#, RTS# change of state
-
0
1
None (default)
相关PDF资料 |
PDF描述 |
|---|---|
| VI-J2H-EZ-S | CONVERTER MOD DC/DC 52V 25W |
| 2-5504971-8 | CA 62.5/125 LDDZP SCDUP SCDUP |
| EEC08DRAS-S734 | CONN EDGECARD 16POS .100 R/A PCB |
| CB5000-000 | HEAT SHRINK TUBING |
| XR16M654IQ100-0B-EB | EVAL BOARD FOR XR16M654-B 100QFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XR16M564IV-0B-EVB | 功能描述:界面开发工具 Eval Board for XR16M564IV-0B RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| XR16M564IV64 | 制造商:EXAR 制造商全称:EXAR 功能描述:1.62V TO 3.63V QUAD UART WITH 32-BYTE FIFO |
| XR16M564IV64-F | 功能描述:UART 接口集成电路 UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR16M564IV80 | 制造商:EXAR 制造商全称:EXAR 功能描述:1.62V TO 3.63V QUAD UART WITH 32-BYTE FIFO |
| XR16M564IV80-0A-EB | 功能描述:界面开发工具 Eval Board for XR16M564IV80-0A RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
发布紧急采购，3分钟左右您将得到回复。