参数资料
| 型号： | XR17C152IM-F |
| 厂商： | Exar Corporation |
| 文件页数： | 31/62页 |
| 文件大小： | 0K |
| 描述： | IC UART PCI BUS DUAL 100TQFP |
| 标准包装： | 90 |
| 特点： | * |
| 通道数： | 2，DUART |
| FIFO's： | 64 字节 |
| 规程： | RS485 |
| 电源电压： | 5V |
| 带自动流量控制功能： | 是 |
| 带IrDA 编码器/解码器： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 100-TQFP |
| 供应商设备封装： | 100-TQFP（14x14） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页当前第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页
á
XR17C152
REV. 1.2.0
5V PCI BUS DUAL UART
37
ISR[4]: Xoff/Xon or Special Character Interrupt Status
This bit is enabled when EFR bit-4 is set to a logic 1. ISR bit-4 indicates that the receiver detected a data
match of the Xoff character(s). If this is an Xoff/Xon interrupt, it can be cleared by a read to the ISR. Reading
the XCHAR register will indicate which character (Xoff or Xon) was received last. If it is a special character
interrupt, it can be cleared by reading ISR or it will automatically clear after the next character is received.
ISR[5]: RTS#/CTS# Interrupt Status
This bit is enabled when EFR bit-4 is set to a logic 1. ISR bit-5 indicates that the CTS# or RTS# has changed
state from LOW to HIGH.
ISR[7:6]: FIFO Enable Status
These bits are set to a logic 0 when the FIFOs are disabled. They are set to a logic 1 when the FIFOs are
enabled.
4.8.6
FIFO Control Register (FCR) - Write-Only
This register is used to enable the FIFOs, clear the FIFOs, set the transmit/receive FIFO trigger levels, and
select the DMA mode (legacy term that refers to "block transfer mode"). The DMA and FIFO modes are
defined as follows:
FCR[0]: TX and RX FIFO Enable
Logic 0 = Disable the transmit and receive FIFO (default).
Logic 1 = Enable the transmit and receive FIFOs. This bit must be set to logic 1 when other FCR bits are
written or they will not be programmed.
FCR[1]: RX FIFO Reset
This bit is only active when FCR bit-0 is active.
Logic 0 = No receive FIFO reset (default).
Logic 1 = Reset the receive FIFO pointers and FIFO level counter logic (the receive shift register is not
cleared or altered). This bit will return to a logic 0 after resetting the FIFO.
FCR[2]: TX FIFO Reset
This bit is only active when FCR bit-0 is active.
Logic 0 = No transmit FIFO reset (default).
Logic 1 = Reset the transmit FIFO pointers and FIFO level counter logic (the transmit shift register is not
cleared or altered). This bit will return to a logic 0 after resetting the FIFO.
FCR[3]: DMA Mode Select
This bit has no effect since TXRDY and RXRDY pins are not available in this device. It is provided for legacy
software. DMA is a legacy term used for block transfer mode. DMA does not stand for "Direct Memory Ac-
cess."
Logic 0 = Set DMA to mode 0 (default).
Logic 1 = Set DMA to mode 1.
FCR[5:4]: Transmit FIFO Trigger Select
(logic 0 = default, TX trigger level = 1)
The FCTR bits 6-7 are associated with these 2 bits by selecting one of the four tables. The 4 user selectable
trigger levels in 4 tables are supported for compatibility reasons. These 2 bits set the trigger level for the
transmit FIFO interrupt. The UART will issue a transmit interrupt when the number of characters in the FIFO
falls below the selected trigger level, or when it gets empty in case that the FIFO did not get filled over the
trigger level on last re-load. Table 14 below shows the selections. EFR bit-4 must be set to ‘1’ before these
bits can be accessed. Note that the receiver and the transmitter cannot use different trigger tables. Whichever
selection is made last applies to both the RX and TX side.
相关PDF资料 |
PDF描述 |
|---|---|
| XR17C154IV | IC UART PCI BUS QUAD 144LQFP |
| XR17C158IV-F | IC UART PCI BUS OCTAL 144LQFP |
| XR17D152CM-F | IC UART PCI BUS DUAL 100TQFP |
| XR17D154CV-F | IC UART PCI BUS QUAD 144LQFP |
| XR17D158IV-F | IC UART PCI BUS OCTAL 144LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XR17C154 | 制造商:EXAR 制造商全称:EXAR 功能描述:5V PCI BUS QUAD UART |
| XR17C154_05 | 制造商:EXAR 制造商全称:EXAR 功能描述:5V PCI BUS QUAD UART |
| XR17C154CV | 功能描述:UART 接口集成电路 UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR17C154CV-0A-EVB | 功能描述:UART 接口集成电路 Supports C154 144 ld TQFP, PCI Interface RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR17C154CV-F | 功能描述:UART 接口集成电路 UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。