参数资料
| 型号： | XR17C152IM-F |
| 厂商： | Exar Corporation |
| 文件页数： | 34/62页 |
| 文件大小： | 0K |
| 描述： | IC UART PCI BUS DUAL 100TQFP |
| 标准包装： | 90 |
| 特点： | * |
| 通道数： | 2，DUART |
| FIFO's： | 64 字节 |
| 规程： | RS485 |
| 电源电压： | 5V |
| 带自动流量控制功能： | 是 |
| 带IrDA 编码器/解码器： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 100-TQFP |
| 供应商设备封装： | 100-TQFP（14x14） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页当前第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页
XR17C152
á
5V PCI BUS DUAL UART
REV. 1.2.0
4
RI0#
70
I
UART channel 0 Ring Indicator or general purpose input (active low). This
input should be connected to VCC when not used.
TX1
62
O
UART channel 1 Transmit Data or infrared transmit data. Normal TXD output
idles HIGH while infrared TXD output idles LOW.
RX1
55
I
UART channel 1 Receive Data or infrared receive data. Normal RXD input
idles HIGH while infrared RXD input idles LOW. In the infrared mode, the
polarity of the incoming RXD signal can be selected via FCTR bit-4. If this bit
is a logic 0, a LOW on the RXD input is considered a mark and if this bit is a
logic 1, a HIGH on the RXD input is considered a space.
RTS1#
60
O
UART channel 1 Request to Send or general purpose output (active low). If
this output is not used, leave it unconnected.
CTS1#
56
I
UART channel 1 Clear to Send or general purpose input (active low). This
input should be connected to VCC when not used.
DTR1#
61
O
UART channel 1 Data Terminal Ready or general purpose output (active low).
If this output is not used, leave it unconnected.
DSR1#
57
I
UART channel 1 Data Set Ready or general purpose input (active low). This
input should be connected to VCC when not used.
CD1#
58
I
UART channel 1 Carrier Detect or general purpose input (active low). This
input should be connected to VCC when not used.
RI1#
59
I
UART channel 1 Ring Indicator or general purpose input (active low). This
input should be connected to VCC when not used.
ANCILLARY SIGNALS
MPIO0-MPIO7
52-45
I/O
Multi-purpose inputs/outputs 0-7. The function of these pin are defined thru
the Configuration Register MPIOSEL, MPIOLVL, MPIOINV, MPIO3T and
MPIOINT
EECK
84
O
Serial clock to EEPROM. An internal clock of CLK divide by 256 is used for
reading the vendor and sub-vendor ID during power up or reset. However, it
can be manually clocked thru the Configuration Register REGB.
EECS
83
O
Chip select to a EEPROM device like 93C46. It is manually selectable thru the
Configuration Register REGB. Requires a pull-up 4.7K ohm resister for exter-
nal sensing of EEPROM during power up. See DAN112 for further details.
EEDI
82
O
Write data to EEPROM device. It is manually accessible thru the Configura-
tion Register REGB. The 152 auto-configuration register interface logic uses
the 16-bit format.
EEDO
81
I
Read data from EEPROM device. It is manually accessible thru the Configu-
ration Register REGB.
XTAL1
77
I
Crystal or external clock input of up to 50MHz for data rate of 3.125Mbps at
5V. See AC Characterization table.
XTAL2
76
O
Crystal or buffered clock output.
TMRCK
75
I
16-bit timer/counter external clock input.
ENIR
74
I
Global Infrared mode enable (active high). This pin is sampled during power
up, following a hardware reset (RST#) or soft-reset (register RESET). It can
be used to start up both UARTs in the infrared mode. The sampled logic state
is transferred to MCR bit-6 in the UART. Software can override this pin there-
after and enable or disable it.
EN485#
65
I
Global AutoRS485 half-duplex direction control enable (active low). During
power up or reset, this pin is sampled and if it is a logic high, both UARTs are
set for Auto RS485 Mode. Also, the Auto RS485 bit, FCTR[5], is set in both
channels. Software can override this pin thereafter and enable or disable it.
Pin Description
NAME
PIN #TYPE
DESCRIPTION
相关PDF资料 |
PDF描述 |
|---|---|
| XR17C154IV | IC UART PCI BUS QUAD 144LQFP |
| XR17C158IV-F | IC UART PCI BUS OCTAL 144LQFP |
| XR17D152CM-F | IC UART PCI BUS DUAL 100TQFP |
| XR17D154CV-F | IC UART PCI BUS QUAD 144LQFP |
| XR17D158IV-F | IC UART PCI BUS OCTAL 144LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XR17C154 | 制造商:EXAR 制造商全称:EXAR 功能描述:5V PCI BUS QUAD UART |
| XR17C154_05 | 制造商:EXAR 制造商全称:EXAR 功能描述:5V PCI BUS QUAD UART |
| XR17C154CV | 功能描述:UART 接口集成电路 UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR17C154CV-0A-EVB | 功能描述:UART 接口集成电路 Supports C154 144 ld TQFP, PCI Interface RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR17C154CV-F | 功能描述:UART 接口集成电路 UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。